Find trusted local electricians in Rochedale South

Ceiling will be installed next week- an electrician needs to check the house on Saturday 8/11 25 and give me a quote asap

My window aircon tries to start makes noise but then dies. I need a quote for repair.

Need a qualified electrician to connect 2x installed outdoor blinds to mains power.

I need to do a few repairs on my roof, and need a few solar panels (7 max) temporary lifted so that the trades can see whether there are any tiles underneath that need to be repaired. The panels need to be re-installed after the repairs.

Install two pendant lights shipped from China, electrician needed

Need an insured and certified electrician to help with 1) Take out the existing sensor headlights and replace with SWAN security cam sensor headlights in the front 2) Take out the existing headlights in the deck area and replace with the sensor headlights which was removed from the front side. 3) Need to replace existing 2 outlet power point with Four or Five Outlet Power Point in the Laundry area

The Split AC is leaking water from the front indoor unit. The unit is diaken. The outer unit is on the top and it’s low set house. Looking for someone to rectify and fix the water leak. The ceiling is 4.2m

I have an electronic switch board that functions as a mother board that operates the pump, lights and refrigerator to see if they are all functioning correctly.

scope of work 1. Disconnect existing freestanding cooktop connected to 32A breaker 2. Install a new ceramic cooktop (6.6kW)) to the exisiting 32A / 6mm2 circuit. Cooktop isolation switch already exisint 3. Install a new 10A plugin oven (max power 2.1kW) to the same 32A cooktop circuit. Jbox already behind the wall. Or, 4. Tie into the 10A GPO nearby but will need to be re-routed Cabinetry and benchtop will be cut to size - no cabinetry work required. My understanding as per the wiring rule both cooktop and oven can run on a same 32A circuit but pls confirm. If a new dedicated circuit is needed for the oven, switchboard is about 3m away from the kitchen - lowset house with roof access. Pic of switchboard attached Location Rochedale South

Remove and change light fitting

Need about 12-14 downlights to be installed around the house and in the alfresco area.

Hello, Are any electricians available. Happy to pay cash or card. I have a Hisense Split System air-con, back to back installation onto a bedroom wall. Thank you.

Supply and install 2 double and 1 single power points. Double powerpoint behind tv. Powerpoint is too close to bed. Require double located further from bed. Single powerpoint at photo 3. Price negotiable.

Our bedroom air conditioner has stopped working. Only licensed air con repairers/installers please. Mitsubishi srk25zsa-w Looking at the manual, looks to be an ‘indoor fan motor error’.

Findings: Something is causing the HWS to trip twice so far and now no power supply at all. Possible faulty circuit breaker or isolation switch. Circuit breaker's maximum capacity 16A while the breaker should technically handle the load, sustained operation at Or near the maximum rating can cause overheating or nuisance tripping.

I have four bedroom house and ducted in whole house . So it need to be clean

New double power point 3 x power switches that wont push on one been the stove

A ceiling lighting base with a circular fluorescent bulb was functioning well with bright light. The bulb is fairly new. Couple of days when had the light turned on, it suddenly went off with no previous warning or indication that it had an issue. When I replaced the used circular fluorescent bulb with a new bulb and as soon as I turned the light on, only one flicker of light appeared for a second and the light did not work at all. I do not think the problem is in the bulb. It could possibly be in in the electronic ballast. If the electronic ballast is to be replaced, my preference is that the base fitting would be still suitable to refit the existing flat glass cover and its oyster glass cover over it. Attached are photos of the lighting base with the bulb taken off and another showing the circular fluorescent bulb type. The external diameter of the metal base is approximately 320 mm which is almost the same size as the opening of the flat glass cover with the opening showing in the attached photo. The depth of the metal base is approximately 30 mm. The fluorescent bulb size is 16 mm and its external diameter is 245 mm as showing in the attached photo of the box. The diameter of the oyster glass cover is 340 mm.

My hot water system has stopped (Heat Pump 15 years old). I am changing to a continuous gas supply and need the wiring that I have disconnected safely to the Heat Pump, attached to an outdoor wall plug that I have purchased.

I dropped the lamp and it looks like the wiring has come loose.