Find experienced local carpenters in Duncraig

Bunnings wood (Hevea modular benchtop) kitchen benches to be cut to size for a smaller kitchen, sink and cooktop to also be cut out. Breakfast bar using same material also to be cut and installed. Breakfast bar sits opposite sink.

Im looking to get a built in wardrobe done to replace the one attached in the photo. I will do the demolition part.

I'm looking for a handyman who has experience installing IKEA benchtop and rangehood appliance The work includes - installing benchtop on the island which is 2400 mm long - install benchtop with sink and stove cutout 2800 mm - install backboard for the island -indtalling rangehood

Build Stratco handipod (Handi-Pod Hinged Door Garden Shed 2170x2285x2040) shed on a pre made concrete base.

Re- assembly of a second hand cubby house. Cubby broken down into larger segments. Screws together. May be a 2 person job as difficult to hold upright and insert screws at same time.

A colorbond cover for Pool equipment. Include flashing and a door. Attached picture has measurements and rough design drawing of the shed/cover.

Require slab for 6x4 shed in Duncraig, will need line pumpbor boom due to slab being at back of property, any more details please message.

Need 1.2m tall section of internal fencing, garden bed width 600, concrete between shed and edge 1100. Thinking about two posts in garden bed with fixed panel and one post adjacent to the shed with gate over concrete slab however open for suggestions. Ideally black aluminium bars, no colour bond. Needs to be in line with pool regulations, so 1.5m high gate opening.

Need corten steel edging cut to size and installed. It is 3mm thick. Approximately 10m linear in total. Need to cut to size to fit garden beds. I have already installed majority, just need final pieces cut to fit.

Finish cabinet installation that was not completed by company that is now in litigation. Most if not all parts are available. Need to cut some to size. Kitchen, laundry and shavers cabinets. Including installation of pocket doors, kickers, finger polls, etc

Finishing work on BIR cabinets and Kitchen Cabinets BIR Cabinets: Fixing new cabinets to 6 Built In spaces and scribing filler panes. Kitchen: Installing kickboards, and installing 6 face panels to kitchen island. Material like filler panels and framing timber is supplied. Looking for someone with experience in this work. Can view and provide offer on site or can offer cost per hour.

Retic pipe leaking at joint. Also at different area spray pipe needs cutting and rejoining and new sprayer put in.

Garden shed is supplied as a metal flatpack with instructions. The job is to assemble each of the four sides and roof where each section has a top and bottom rail and abut 4 sheets of metal siding. Two roof sections are much the same. Assembly is mainly fastening all the bits together with supplied Tec Screws. Several items such as two doors and a window frame need to be pop rivetted in with supplied fasteners. The shed also needs to be fastened to a concrete slab with 8 x 10mm x 100mm bolts suppled. The finished unit is 3m x 3.7m x 2.4m high,

Assemble a new 3x2 garden shed

I need a stained glass motive fixed on my front door.

assemble flat pack skillion roof shed on exist paving block floor. 3m x 1.9 m - Due date: Flexible

Kitchen Benchtop cut and Install Kaboodle Modules to be levelled prior to Benchtop Installation Standard Veneer Benchtop , no Stone - Due date: Flexible

We have workstations in a small office in Carine. We have just moved in and brought the workstation parts with us. We brought metal legs and supports but the legs and supports now don't appear to match. (they were in storage). The photo shows 4 workstation tops. We need to add legs. then assembled on site. Just need someone who can make the stands out of chipboard. - Due date: Needs to be done on Friday, 14 July 2023

Formica/Laminex bench top replaced and new runners for bin drawer. - Due date: Before Monday, 29 May 2023

I am building a custom piece of exercise equipment and need a piece of 16mm craft wood trimmed in vinyl to make a cushioned seat. It will require the supply of the vinyl (in satin / matt black) and the foam / cushioning material (approx 20mm thick), and the trimming of the board (which I will supply already cut to size). Please see image attached. - Due date: Before Friday, 9 June 2023