Find experienced local carpenters in Canterbury NSW

Kitchen cupboard has randomly stopped closing. I think there is an issue with the hinges but not 100% sure.

Install a bathroom shaving cabinet on tiled wall.

Carpenter needed to repair bed. Need to nail side rail of bed to headboard slat. The bed frame was pulled in the wrong direction, and so screwed-in side rail got disconnected from headboard slat. Should take less than 30 minutes to an hour, to re-screw or nail in.

We just moved in and the top of our fridge is hitting the bottom of cabinet doors. We managed to get the doors off but need someone to come and attach slightly higher so they don’t hit the fridge. There’s enough room at the top to lift them the amount we need. One of the hinges is very close to the fuse box and we struggled to get our screwdriver in there. Looking to get fixed asap.

Hello, We had reclaimed wooden benchtops installed and are unhappy with the mark on one of them. Option 1 We would like to have this piece cut out and a new piece installed. Happy to discuss the best way to do this and the best size of the piece to remove. We have a piece that covers the entire size from the cupboard to the stove stop. Or could we just replace a small section at the front? I'm aware this would add a join but think this is better than the current mark. Option 2 Sand and refine this area. This has already been sanded and is now lower than the surrounding area so am wary to sand more but potentially this is an option.

Hello, We would like someone to cut and install wooden benchtops for our new kitchen and laundy. We are getting reclaimed timber and it will need to be cut and installed as follows. Measurements are approximate. We'd also like the edges rounded. Kitchen bench 1: (thin bench on left hand side ofplan): 2220 X 300 Kitchen bench 2: L shaped: 1904 (under window with cut out for sink) and 1535 (with cut out for stove top). Depth is 600. Wastewood mentioned that this would be two pieces with a join (or if it needs to be more than two pieces, please let me know). I've measured with the join on the longer side of the bench (i.e. not under the window) but happy for this to be moved. Note that the darker yellow section is a pantry so no bench needed there. Laundry bench: L shaped: 1600 (with cut out for sink) x 1000. Depth is 600. Happy for joins as needed. I have also attached photos of the current kitchen. The benches will be the same as the current benches expect there will be an in bench oven rather than standalone. The laundry does not currently have benches to photograph. Our cupboards are being installed on the 16-17 Feb so after this but as soon as possible after would be great for install. We would also like to include pick up of the benchtops (X2) and delivery from Marrickville. They're 2.2m long but can be cut shorter before pick up if needed and in line with the install requirements. If delivery is not possible, we can sort that part. Thank you! Rose

The drawer bottom panel groove is on the wrong side, so the base doesn’t fit. It needs a new groove, it’s about 40cm. I can bring the drawer to you. Should be a quick, simple fix.

Needing an extra set of hands for the day tomorrow to assist my husband with assorted finishing jobs on our renovation incl. - installing skirting board in 1 bedroom - installing trim on floating floor in 2 bedrooms - installing kickboard in kitchen if there’s time

Replace 2 x internal doors, jamb and trim. Cut 1 x solid internal door to size, hang and build out jamb to fit. Materials provided.

Wooden table has burn mark from candle. Will pay for materials required to fix.

There are in total 6 doors. 5 doors are already removed. The bottom edges need to be filed down and then fixed. Sample photos attached.

Needing some to install ready bought cabinets in a laundry room

- Remove doors - Remove shelf - Cut and remove top panel - Cut and remove base - Cut and remove kick board

I’m looking for someone to build a simple and minimalistic wooden support stand for my DJ equipment (2 CDJs). The stand needs to: - Be sturdy and capable of supporting the weight of the CDJs. - Have an angled design for ergonomic use. - Be made from wood (I can supply the material). - Dimensions: 610mm (width) x 400mm (depth) x 400mm (height). - I’ve attached a drawing guide to provide a clearer idea of the design. Clean craftsmanship and functionality are key. Let me know if you can assist and feel free to share examples of similar projects if available. 😊 Please send me some quotes? happy to discuss the price Thanks

Need to fix the wooden drawers of my side table

Line kitchen cabinet with timber panels. Replace skirting board

replace some interior and exterior wood panels

I'm looking to get a quote on installing a Vanity, Mirror Cabinet and Tallboy Wall Cabinet that I rencently bought into my bathroom. The existing Vanity and Mirror will need to be removed. The handtowel holder will need to be relocated. -Vanity is 750mm wide, freestanding and includes sink. Wanting to use existing tap and pipes. The old Vanity is 600mm wide. -The Mirror Wall Cabinet is 1500mm wide to be installed above vanity and toilet. -The Tallboy Wall Cabinet is 400W×300D×1350Hmm and to be installed on the wall next to the towel rail at about 1f off the ground. Included at two photos of my bathroom along with images of the bathroom cabinets.

We have ordered a 800mm x 800mm x 150mm rectangle wooden dog crate and we need to get it from the downstairs car port to the balcony upstairs. The stairs have spirals at the top and bottom making it difficult. There is an option to have it hoisted over the balcony rails. - Due date: Flexible

As per description. MDF material is fine as need white finish. - Due date: Flexible