Find experienced local carpenters in ACT

Recently install gas cook top & gas plumber unable to fixed the kitchen drawer as power shocked back side wall is between , so need to adjust drawer to make it fit

Hi there, We are currently looking for an experienced joiner to assist with a joinery issue, as shown in the attached photo. The existing unit will need to be carefully realigned, pulled out, and re-installed to correct the issue. Additionally, we will need to allow space for a power point on the right-hand side of the panel. Please let us know your availability and if you require a site visit to assess before proceeding.

Looking for a cabinetmaker - I need to move microwave to an existing base cabinet (there is an existing power point) and cut and resize the door to fit bottom cabinet only.

Replace moist architrave and skirting board, plus a small part of an additional skirting board

We have a large aquarium stand (70cm high x 75cm wide, the grey frame) that we need to enclose with two custom-made doors. These doors should allow easy access to the filtration system underneath the tank. We’re flexible on the type of wood, but ideally it should match the existing finish on the stand’s roof. Please note: - The aquarium is full and cannot be moved. - Once the doors are ready, we can either install them ourselves or you’re welcome to handle installation—please quote accordingly. If you're interested or have any questions, feel free to get in touch!

Need to check if the timber frame that has deteriorated due to water leak need to be replaced/fixed and the plastering of the wall that was cut

Require the gap between IKEA walk in robes and the wall to be filled. Details: - Suitable infill panel cut to size and fitted - Skirting panels to be continued across infill panel. No painting required, I will do this after fitting. Thanks

Need a cabinet with three deep drawers.white plain cabinet.height-100 cm ;length -285cm and depth is 30-35 cm

Pull out laundry draw has broken

I have an antique dresser which I am turning into a bathroom vanity, and I need the drawers cut to make room for plumbing. I have cut out inserts, just don't have a saw sharp enough for the hardwood.

I have a coffee table that has a wood frame and it is a bit high, I’d like to shorten the legs evenly so it is stable, and I’m open to further cost for an offer to refinish it. Approx 100cm x 50cm x 60cm high. Granite top shown pops off.

Spot clean of some car oil stains from car park spot.

I need some one to build a dog ramp for our elderly grey hound so he can get down the stairs and into the yard. About 2mx50cm (will provide specific measurements). It will need to have some sort of grip added to the surface to help him up and down.

Sand and stain front door and door frame with two coats I'll supply the stain you will need to provide your own tools

Sand and stain 1 x table and 6 x chairs I'll provide the stain you will need to supply your tools

Looking for cabinet maker who can design and fit cabinet similar to the photo, Height 2700 Length 1600

Sand and stain (2 coats) sun damaged french door. You need to supply sanding equipment and I'll supply the water based stain. Please advise how soon you can do the work.

The kitchen bench got damaged and I need to fix it. Just requires light sanding and refinishing. There is a little caulking on the bench where it connects with the stainless steel bench and splashback. So you would need to remove the existing caulking and recaulk. If you could start today that would be ideal you complete by Thursday morning. When recaulking you will then need to do around the whole kitchen bench under the splashback and window. Pictures attached.

I have a hallway table that is about 3mm too wide for the VERY snug entry way space. Looking for someone with a wood plane - to shave off the 3-4mm needed to make the table fit. Total surface area needing removal is: Two sides, each 21.5cm H x 40cm W If you have sanding/polishing equipment - that would be helpful also. Would need to do work in situ (at my place) so we can test when it is enough to fit.

I need an approx 3-5cm hole drilled in the side of a cabinet for a cable, then a cable grommet fitted (which I will supply)