Find a professional garage door installer in NSW

Supply & Install New Automatic Roller Garage Door Looking for an experienced garage-door installer to supply and install a brand-new ribbed steel roller door, matching the style and appearance of the existing door shown in the attached photo. Approximate size: * 3000 mm wide * 2450 mm high * Traditional ribbed/corrugated roller-door profile * Colour to closely match the existing cream door * Electric motor with remote-control access * Minimum two remote controls We will remove and dispose of the existing door before installation. The job is for the supply and complete installation of the new door only. Your offer must include: * New custom-sized roller door * Tracks, brackets and all fittings * Electric motor and two remotes * Delivery * Installation, programming and testing * GST and warranty details Final measurements can be confirmed on-site before manufacturing. Please provide your best all-inclusive price and earliest availability.

Garage door not closing properly because bottom panel damaged

Currently we have 2 single garage doors with a pillar in between. Task is to remove the pillar, restore stability, install 1 double garage door.

Looking for an experienced handyman or electrician to install two Meross Smart Garage Door Openers on my existing Doorworks 1200 motors. Scope of Work: Connect 2-wire signal cables to the existing dry-contact push terminals (WALL SWITCH and COM) on top of both motors. Install and neatly route the wired door open/close magnetic sensors along the top rail/tracks. Plug both units into the overhead power points and tidy up the wiring. Important Equipment Note: Garage ceiling is approx 4.4m high, with motors suspended at around 3.8m in the center of the garage (no wall to lean against). You must bring an 8ft (2.4m) or larger freestanding A-frame / double-sided ladder. Location: Baulkham Hills, NSW

Hi, I'm looking to replace 2 outdoor doors, 1 for laundry and 1 for garage and architrave, Also looking at repainting garage door.

Need to make a couple of changes to my garage doors. What I need is the one on the right, I need the motor moved about a metre towards the garage and the chain adjusted to allow the garage door to still open (doesn’t have to open all the way), and then the one on the left I want to remove the motor and the tracks and make it a fixed garage panel which won’t be opened. I’m located at baulkham hills.

I have a garage door that the locks needs to changing and 2 pad locks to be added I have the locks and brackets

Looking for someone experienced in Paintless Dent Repair (PDR) / glue-pull dent removal to repair several dents in an insulated garage door in Norwest. The garage door still works perfectly. I just need the dents improved or removed as much as possible. Because the door is insulated, there is limited access from behind, so I’m looking for someone such as a car dent/PDR specialist who can use glue-pulling tabs, dent lifters, a slide hammer and heat if required to work the dents from the outside. I’m trying to avoid replacing the entire garage door panel. Please refer to the attached photos for the damage. If you have experience with PDR/glue-pull dent removal and think you can improve the dents, please make an offer.

I want to replace the existing D&D SDO-2V2 garage opener motor with B&D SDO-7V3 motor. I will supply the Opener motor.

See pics. Need new Garage door remote programmed from old remote Two spare. fobs.

Need to fix/replace 2 panels in a garage door.

Paint garage door white - same colour as house

Hi - our garage door has dropped from the main hinge. I need 2 experienced tradies to help reattach. Photos to be uploaded very soon.

Looking for an experienced handyman/carpenter. Main job (priority): * Replace an existing garage access door. * Existing door is 815mm x 2040mm. * I already have the replacement door (correct width, slightly taller and will need trimming to fit). * Reuse existing hinges and door handle if possible. Also if time permits (happy to discuss): * Fill a few small holes within the house * Sand and paint two door trims (paint supplied). Please bring your own tools. Experience hanging doors is preferred. Photos of the existing and replacement door are attached.

Garage door needs to be sand and paint ! It is timber

Budget is call out fee only. Current motor: ATA GDO-9 Enduro Power point is working, but the motor has no lights and stopped working. Please include: * Remove the old motor * Disconnect/remove the existing white control cable to the wall switch (if needed) * Supply and install new motor * Setup and test remotes

Im looking for someone to paint my garage door. It will need some sanding and prepping as there is some old paint peeling off etc. I have the paint ready to go!

I have a GDO-8 door opener. I need to reset the top and bottom limits. Also to program x3 remotes (which I have)

Re-align down pipe into drain

Please send through offers. Job obviously not for $10 😝 Need someone experienced with sectional/panel lift garage doors to repair an Ultralift garage door. One of the lift cables has detached completely from the drum/bracket area. The cable does not appear snapped, but the door is currently not being operated for safety reasons and will likely need the cable reattached, door re-tensioned/aligned and checked over. Door is currently closed. Please only quote if experienced with garage door repairs and torsion spring systems. Located in Revesby NSW. From my understanding this should hopefully be a fairly standard repair if no additional parts are damaged