Find professional window and door services in Ballarat

Need someone to put together the sliding door panel and install please

It's a tenanted 2-bedroom single storey unit. Upon completion, please send me a few photos and video clips. The address is 4/5 Munro St, Alfredton. You need to have your own work cover and insurance, etc.. I need a new internal door installed. The door needs to be painted in a similar colour to other doors inside the house which is dark blue. The door needs to open towards the window as shown in the floor plan attached. As you can see it has brick walls. Some tasks involved are : - Framing to attach door jamb - Install door jamb - Install door - Install handle - Install Architrave & doorstop Preferably the job would be completed this week.

We have a sliding door that only closes half way before it gets stuck.

needs refitting as has shifted

I have a second hand Rollerdoor with all the side rails to be put up on my shed.

My patio glass sliding door needs a dog door, made into it any suggestions are welcome

Needing two security screens/doors fitted for existing sliding door area and flywire for one small window. Measurements Window 270 x 1300cm Sliding door laundry 700x1900cm Sliding door 900 x 2040cm Refer to photo as an example of the security screens were after and photos of the current doors.

Need a cat flap installed on a door. You will need to bring your own tools. Cat flap provided.

I need a carpenter or handyman to adjust two doors that are currently dragging on the carpet and cannot open fully.

A handyman to install a pet door on wood door, install basket ball hoop on garage, install coat rack and hang a mirror.

Need someone to repair my garage door. The garage door was accidentally closed while the car was still partly underneath, which caused the door to become tilted/misaligned. Looking for someone experienced who can straighten it and get it working properly again. Can provide photos/videos of the damage. Located in Melbourne.

Our garage is being converted to a studio so I’m needing the electric roller door to be taken down.

Please install 1. Cat door 2. Pull up bar I have already purchased the door and bar

hello! I am looking to have a cat door and a door handle installed to a door. Not yet 100% sure if the door is honeycomb or poly core, still need to grab it (will pay $50 more if you can pick the door up from Bunnings and transport it to my residence). Don’t need to take the door off OR install it. Just need the holes cut and the pieces put in. Images include the installation instructions. IDEALLY tomorrow, Tuesday or next weekend. Thanks!

Take old door off ,put new door on ,plane 5mm off ,put knobs ,hinges on

Mortar around where a new door have been installed on a rock wall, ideally can colour it to match the older stuff. Clean up and leave the timber clean and space how it was.

I need a set of 'barn door' sliding doors fixed so they slide on the bottom guide correctly and stay closed when closed and align together. This possibly requires some corrective routing along the bottom of the doors (as its a little wonky) to make them run straight and runner guides re-installed on the floor (as they are floating at the moment and will not stay closed). So I am looking for someone with strong carpentry skills as there are a number of smaller carpentry related (and other 'fix-it' jobs that are required. Will provide any materials. Need someone who is located locally as there are potentially further jobs.

Handyman Needed – Small Job Need someone to: • Hang wall painting on a gypsum board wall • Mount/install a doorbell at the front door Must bring basic tools (Drill) and wall anchors suitable for gypsum board walls if possible. Location: Lucas Flexible timing.

Supply four, cut to length and install (screwed not stick) onto two sets of slim double doors. https://www.bunnings.com.au/moroday-915mm-black-mds5-compact-door-seal_p0106993?store=6442

I need the door to my crawl space repaired and reattached with a latch and slightly higher than it was before. I have sanded it down but it needs a little more work done to it which I could have done had I not injured my hand. I have the hardware and tools (if needed) for the task.