Find an experienced retaining wall contractor in QLD

Have shit retaining walls and need someone to dig out behind and remove the concrete sleepers without damaging them and have them stacked to the side. Possibly a day rate? Or hourly rate?

We have 7 concrete sleepers against our retaining walls that we would like to get cut flush against the retaining wall.

Need building approval for a retaining wall 1.9m on the highest side. Fence on top. Engineer certificates all available

Need to put steel posts into a hole for retaining wall.

Roughly 35 meters long possibly 1 metre high

Concrete retaining sleeper wall one side 4.5m and one 20m. Also need back wooden fence 20m length and 1.8m high.

installers needed for fencing, retaining walls

Request quote from an experienced bricklayer to prepare an existing brick retaining wall for a new fence. Scope of work includes- * Build brick pillars at suitable spacing for the new fence. * Existing retaining wall may need to be extended/raised in sections to accommodate the pillars and fence. * Ensure pillars are securely tied into the existing brickwork and suitable for the future fence. * Photos, measurements and fence design can be provided. * Please quote labour and materials separately if possible. I am after a quality, practical and cost-effective job. Please provide your best quote and availability.

Need all paint ground off this retaining wall

Require renderer to touch up existing rendered retaining wall and also render new section installed. Approximately 1.5m long x 0.5m of new wall.

I need a timber sleeper installed underneath the existing retaining wall. The sleeper is needed to close off the gap underneath the retaining wall so concrete can be poured up to the wall without spilling underneath. The ground slopes, so the sleeper will need to be cut to follow the slope/angle of the ground so it fits neatly into the gap. I haven’t measured the gap yet, so I’d like someone who can measure it, cut the timber to fit and install it securely. Timing: Needs to be completed before Tuesday. Photos attached.

1 of the sandstone blocks was knocked out of place and needs to be lifted & put back in place by a stone mason or landscaper. The sandstone probably weighs Around 120-150kg & is the end block next to our driveway

Front loader TLC washing machine retaining ring snap fix . Put retaining ring back.

We require additional sleepers on the existing retaining wall. Welding will be required

Just need this one section of hardwood sleepers and the small supporting posts removed from this front yard garden. Pulled out, dug up or chopped up, however possible for it to be yanked out of the ground. Termite risk so need removed. These are in the front yard and are accessible any time of day for removal. Varsity Lakes near the varsity train station.

I bought some retaining wall bricks for the yard and they were the wrong size (as shown in the photos) on the left side. Rather than replacing them I just need to move about 15 of them from behind the shed (shown in the photos) over to the area behind the pool to sensor the sizes all match. Just had surgery so I am unable to do it myself.

I have two PFC posts concreted in place at my house. I need them stitched together. You will need a caddy welder to access site. The steel is about 6mm thick.

I have a retaining wall to be re painted and a timber fence painted

Need someone to lay the concrete footings for a DIY low retaining wall. I’m planning on building using Versawall blocks, but want someone with more experience to make sure the footings are level. The wall is only 800mm high so requirements are 450mm wide but 130mm deep. The total length is 10metres (3m + 4m + 3m - see photo of the hole in the garden that is getting retained) Concrete Taxi can deliver the concrete needed and ready to go for $445, so really just need someone with the skills and experience to make sure it’s level. Planning on this being done middle of next week (15, 16 or 17 April)

Need someone to finish a brick retaining wall flush to the boundary wall. The length is about 1.5m and only 3 bricks high. because I want it flush to the boundary wall, some brick cutting is required. the bricks are 13cm deep.