Find an experienced door installer in East Melbourne

1. DOOR - Ensuite Bathroom Door Installation - (SUPPLY & INSTALL) * Request/Issue - Modify opening and install new timber door. * Location - Ensuite bathroom. * Size/Area - Approx. 1200mm × 2500mm opening. * Type - Plasterboa tity - 1 door. ~ Assess opening and confirm optimal hinge orientation. ~ Protect flooring, vanity and surrounding finishes. ~ Remove existing skirting and trim from end wall. ~ Remove existing roller blind and fixing brackets. ~ Remove top and bottom architraves to window. ~ Construct new stud framing to reduce height and width of opening. ~ Install new plasterboard sheeting to framed section. ~ Tape, set and sand joints to paint-ready finish. ~ Install new door jamb to new door opening. ~ Install new architrave to door to match existing profile. ~ Install new architrave to close off gaps between new wall and window. ~ Fill, sand and prepare all fixing points. ~ Supply and install new internal door and hardware. ~ Prime all new plasterboard and raw timber. ~ Apply two coats colour matched wall paint to new section. ~ Apply two coats semi-gloss enamel to door, jamb and architrave.

I need a cat door installed in a room that has plasterboard on the interior wall and aluminium cladding on the exterior. I will supply the cat door myself. I just need assisstance installing it. Thanks!

Looking for an experienced person to remove, transport, and drop off a 4.3 metre roller door and its components. Scope of works: • Carefully remove existing 4.3m roller door in Kew • Disassemble and secure all components (curtain, tracks, brackets, motor if applicable) • Transport safely to Richmond • Unload and place neatly onsite Important: • Must have proven experience removing roller doors • Must bring appropriate tools • Door is large (4.3m wide), so suitable vehicle/trailer required • Care must be taken to avoid damage to door or property Location: • Pick up: Kew • Drop off: Richmond Date & Time: • Tuesday 3 March – Morning (time to be confirmed) Please confirm: • Your experience with roller doors • Vehicle type • Availability Tuesday morning Looking for someone reliable and experienced only.

Details -Door type: single tilt door (standard size) -Condition:The door is app.40yrs but currently operating manually. -Scope of work:1.supply and install a reliable brand motor (eg. Merlin Tiltmaster or equivalent) suitable for a tilt door. 2.Conduct a general service of the existing door (lubrication and spring tension adjustment)to ensure it's safe for automation. 3. Program 2-3remote controls. -Power: There is a power point near the door. Requirements; -please have prior experience specially with the tilt doors. -The door must be tested for safety after installation. -please provide a warranty for the motor and workmanship. Looking forward to your quotes Photos of the internal mechanism are attached.

Hey there I am hoping to replace both my exterior doors. The green door with colourbond gate and white door with colourbond door please. Including the door frames for both of them.

There’s a room which was used before as study but now we want to convert it as a room so for that weed to install a slider door on that frame

I need someone to replace this door. It must be exactly the same design as the townhouse complex. I can pay for the door separately if needed. Replacement only and no staining required.

We want to replace the manual roller door with an electric one. 3 phase switchboard is within 4 metres of the door. We have a team of electricians who can assist with removing the old and installing the new - and also certify the electrical work. Replacement product must be wifi enabled.

We need a dog door installed in a French sliding door. There is a panel on the right that stays stationary for it to be installed in.

Hello I already have the cat door I just need it installed in Bulleen ASAP

-Replace 2 doors, and change their direction, and put door lock -change door lock for one other door Please put your best offer

I need a qualified electrician to replace an existing wired doorbell with another wired doorbell (in same place) with video intercom.

We have just had the house painted and all of the door handles are being replaced. Holes already there.

Needing to replace one side of door jamb so that the security screen lock is in line with the jamb

Need to replace door jamb on one side and replace the security/fly screen

Need to replace a door (new door was ordered to have same dimensions as the old) plus move existing handle to new door and install smart lock (Tapo DL110). Handle, new door, lock are ready.

I need a lock installed on a door

Supply and install 1500mm beige base-of-frame door seal to replace existing seal. New seal should match existing seal on sides and top of frame.

Front door installation required asap.

One flush mount panel door W4000xH2400; one roller door W1600xH2400