Find a professional gate installation in East Brisbane

My side gate hinges have broken . Need to have them replaced 4 x external gate hinges put back on and gate operational again It’s two swinging gates that connect Hinges to be provided by installer

Repair hole in plaster wall and install child security gate at top of stairs asap

Issue with sensor - the gate opens fine but if you drive through a bit late while it's starting to close the safety triggers to reopen (as it should) however once it reopens it gets stuck in the open position. It refuses to close again unless I completely reset the system (sometimes it takes 2 resets to get it working again)

Hi, I’m looking for someone experienced to supply and install a gate for my backyard. Details: • Opening width: 3.9 meters • I would prefer a Colorbond gate if possible • The gate needs to be strong and secure • It will likely require posts, hinges, and full installation Because the opening is quite wide, it may need to be: • Double swing gate, or • Sliding gate I’m happy to take advice on the best option. Please include: • Your experience with installing gates/fences • Estimated price (including materials if possible) • Availability Thanks.

I have 2 gates Filo 400 with Controller CL101 - I have approximately 8 Remotes- ECC05B0 / two wifi controllers Bidi-Wifi and an external keypad EDSWG I need them programmed. its not all working properly I would suggest factory reset on all and all keys are repaired.

Need remotes programmed to gate motor Motor installed and have the remotes Touch pad to be programmed to open gate as well Have all the gear

Slide gate main entering .not working properly

Need new remotes and control panel for electric gate for house. Only 1 remote - driving us insane! Keypad entry is not working.

I am looking for a custom gate for our stairs to match our existing balustrade and stringers. We can do the staining. I have mocked up some pics on ChatGPT… something similar to what is pictured. Unsure if we will need to do a single or double gate. Will need good baby proof latch too.

I’m looking for a qualified person to supply and install a 1.8 m‑high PVC picket‑style privacy gate on both sides of my property. Please see attached photo with red circle for indication. The total length required would be around 5-6 meters. Scope of work: -Supply and install 1.8m PVC picket privacy fence - Include one gate on each side, PVC material, matching style - Gate width: 1.5m - All materials, posts, hardware, and labour to be included - Must be durable, low‑maintenance PVC suitable for outdoor use - Please provide photos of previous similar work if possible

One hinge on outdoor fate needs replacing and some boards nailed back on. And wooden fence has some loose pailings that need securing with nails.

I need a white timber or PVC gate installed at the front of my townhouse. It needs to match the vibe of the building see photos attached, and the idea of it is to open outwards so we can reduce the likelihood of my dog escaping when the front door gets opened. Vertical slats similar to the one pictured but dimensions are higher - 149cm wide x 179cm high.

I need new remotes programmed with our Nice Hi-Speed gate (RUN1200 HS) ASAP I think I have the wrong remotes so would need those also

4 holes dug approx 600mm deep to install gate post, will need to have a jackhammer as a couple of the holes are to be installed next to the house

The gate is leaning and difficult to shut without lifting the left hand side. Ideally I’d like to keep the two panels of gate, replace or realign the posts on either side, then rehang the existing gate so it’s an easy close. Flat yard, easy side access, power and water close by, quiet cul de sac location with driveway parking.

Fence needs to be resecured with screws and gate hinge reattached/reinforced,

Supply & install approx. 8m of Colorbond fencing (two sections approx. 2m and 6m) with two gates. At least one gate must be lockable with a keyed outdoor lock. Standard residential Colorbond colours acceptable. Looking for a simple, cost-effective solution and happy to be flexible on timing.

Install 2 x dreambaby retractable gate to inside of 2 openings

​Task Description: Hi! I have recently built a pool fence around my spa and need an experienced welder to finish the job by welding the gate together. ​Requirements: ​Must have experience welding aluminum. ​Must provide their own welding equipment (TIG or MIG setup capable of aluminum). ​The gate components are already cut/prepped ​Looking for clean, strong welds that meet safety standards for a pool area. ​Please let me know your experience level and what equipment you’ll be bringing. Thanks!

Dual 900mm towel rack in ensuite shower needing to be reattached to wall, grub screw appears to not be moving. Possibly need a new one on inspection and will pay for the materials if required. Also, reattach gate latch with required screws (I don't have these)