Find a local glass fencing contractor in QLD

Supply & Install Spa Pool Fencing – Glass Front & White Aluminium Sides (Toowoomba) Looking for an experienced pool fencing installer to supply and install compliant fencing around our newly installed outdoor spa in Toowoomba. The spa sits on a 3m x 3m concrete slab, with an existing 1.8m Colorbond boundary fence at the rear. We’re looking for: * Clear glass fencing across the front, including a self-closing, self-latching gate aligned with the existing brick pathway. * White aluminium flat-top pool fencing along both sides. * Supply and installation of all panels, posts, gate, hinges, latch and fittings. * Fencing that meets Queensland pool safety requirements. We’re also planning a sand-coloured shade sail supported by approximately 2.5m-high Paperbark-coloured posts. Ideally, we’d like these posts incorporated into the fencing layout where practical, although the shade sail installation itself is not part of this task. We’re currently arranging building certification for the spa, so the fencing design and installation will need to meet our certifier’s requirements. Photos and measurements are available, and we’re happy to arrange a site visit. Budget is indicative only. Please provide your best quote for complete supply and installation.

Need our pool fence replaced, please include disposal of existing in offer. I can supply frameless if necessary. 10m length.

Hi, I need a QBCC licensed glazier / pool fencing installer for my frameless glass pool fence job at Ormiston QLD. ✅ What I supply: All glass panels already on-site. The glass is 12mm Grade A toughened safety glass, marked AS/NZS 2208, CSI 7078, PAS-Mark etched on every panel (photos attached). This is second-hand glass purchased privately, original manufacturer contact is unavailable. ✅ Work required: 1. Professional installation of the frameless glass pool fence (approx total length ~10.65m, including gate panel) to comply with AS1926.1 Queensland pool barrier standard. ​ 2. Issue a formal glass compliance statement / glazing certificate (signed, QBCC compliant) confirming this 12mm Grade A toughened AS/NZS2208 glass is suitable for pool balustrade use. This document must be acceptable to my private building certifier for pool approval (Form 16 / building approval). Important note: My private certifier requires this supporting glass document because I do not have the original manufacturer test reports for these second-hand panels. ❌ Not required: I am NOT asking for full Pool Safety Certificate (Pool Safety Inspector certificate) at this stage, just installation + glass compliance statement for building approval. Requirements for you: - Must hold valid QBCC licence for glazing / pool fencing work ​ - Proven experience supplying glass compliance statements for QLD pool certifiers ​ - Can provide references of similar second-hand glass pool fence certification jobs ​ - Can quote labour only (all glass panels provided by me; we can discuss spigots, gate hardware separately) Please send your quote, availability and licence number when responding.

Apply new magna latch to poōl gate certified standards & 2 small brackets

Bunnings mimosa pergola 4 x 3sqm and Bunnings pool fencing circa 5 meters and a gate. All are to be bolted to existing new concrete.

Install A Glass Fence Door to side of the house. Install a Glass fence panel side of the house (check the picture) Level the Glass fence around the house and tighten any loose panels(Maintenance) Must have appropriate tool to do the Task All Material is supplied by the site owner you only supply the labour

I need help installing a glass panel pool fence. With one gate . I will have all the materials available

Instal the Glass Pool Fence and align all (I.e finish to full completion) About 10M remaining, but about 20M total LM. I have all the pooling glass materials, gates, latches etc. Please quote

2 glass gates installed into both rock and wood

Drill posts and add glass pool panels back in place. Fix or redo glass pool gate in shallow end. My husband can assist if needed as pool panels are heavy.

Reinstall pool fence post into tiles.re attached glass pane into fence holds

Looking for someone experienced with pool/spa fencing to install a small aluminium fence and gate onto existing exposed aggregate concrete. Everything is already supplied. The job consists of: * 1 × 970 mm aluminium gate * 1 × 2090 mm aluminium fence panel * 2 × base-plated aluminium posts * SafeTech self-closing hinges and pool latch * Brackets, screws and M10 stainless Dynabolts supplied One panel will need to be cut to size. Posts need to be drilled and Dynabolted into the existing exposed aggregate concrete, then the panel and gate installed, levelled and adjusted. Must have your own SDS/rotary hammer drill and appropriate tools. As this is a spa safety barrier, I’m looking for someone with pool-fence installation experience who can ensure the gate is correctly positioned, self-closing and self-latching.

The pool glass door is not shutting properly. Need to check and fix the issue.

Glass panels are all slowly coming undone and wonkey as ground has moved and posts done align with glass any more. I have had a few panels done with additional spigot support but I want the lot done now: removing the posts and replace with spigots. 10-12 panels need spigots, depending on what’s possible on either end (might need to leave some posts in, especially with the door): I have sourced spigots already. Scope of task: - assess and recommend best way forward with the end and door panels - remove and replace posts with spigots: 10-12 panels - supply tools: to drill holes into tiles without wrecking them - other bits and bobs needed: bolts etc - remove posts from premises: dump run etc Location is Ipswich central. Thanks Oliver Edit: I just realized I did not adjust the budget since I had this task online last time given I have now sourced spigots already and they’re not included in task any more.

We have purchased a house (20yr old) that council has failed for pool compliance. It has a servery window which bi-folds back and once opened stacks approx 40cms from the pool fence. So is deemed as climbable and non compliant. We require a 600h x 800l x 12mm thick clear Perspex and o be attached to the house & top of glass fencing temporarily for compliance. Needs to be done by Friday 5pm

I have been given a non compliant pool fence notice . There are various repairs including - sections around gate where fence is 5mm too short. Possible packers needed under posts. - some retaining structures are too close, possibly replace fence panel with taller panel or use Perspex shield - gate and latch adjustments

Please can you quote me to install glass fencing around the pool. 9.57m along the long side and 5.9m across the short side. The are to the right on the short side needs some concrete between the pool and the wooden garden fence.

We have an existing glass pool fence that requires repair. The stainless steel spigots are in good condition, however the anchor fixings have rusted and need to be replaced. Note that each glass panel will need to be removed to access the bracket fixing points (2 person lift that I can assist with).

Hoping someone can come with a grinder to help cut pool fence (removed) spigot. Happy for it to be completely removed as well, whatever is easier. Thanks.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.