Find a local glass fencing contractor in QLD

Pool Fence Repairs Required – Make Pool Barrier Compliant (QLD Pool Safety Certificate) I am looking for an experienced pool fencing contractor or handyman with knowledge of Queensland pool safety regulations to repair my pool barrier so it complies with the Queensland Pool Safety Standard and passes a re-inspection for a Pool Safety Certificate. The inspection identified the following items that need to be rectified: * Repair or adjust the pool gate so it self-closes and self-latches from all positions. * Secure the loose fence around the gate area. * Repair or replace broken vertical pickets. * Modify the non-climbable zone (NCZ) where a wall reduces the effective barrier height below 1200mm. * Remove or modify the climbable attachment on the boundary fence. * Reduce a gap at the rear of the fence to less than 90mm. Please provide: * Your experience with Queensland pool fence compliance. * A fixed price or an estimate after reviewing photos or inspecting the property. * Availability to complete the work as soon as possible. The goal is to have the pool barrier fully compliant and ready to pass the follow-up pool safety inspection.

The glass sections are on top of a low cement rendered wall at the back of the house and the aluminium sections will run through a garden. We may also replace the current boundary aluminum fence which runs along the top of a block wall. I have no idea of the cost to put in under the budget section i'm happy to discuss this with you once you have seen the job

Glass pool installer required about 15metre including gates all materials from glass panel to dyna bolt and sikka will be provided from me. In whiterock Qld 4306 quote thanks in advance

We set this glass fence up so our dog couldn’t access the sliding door. We would now like to move the entire glass fence back from the bottom of the stairs and preferably just one gate. We have a quote from a builder. Please quote your best price inclusive of any materials

looking for an experienced pool fencing installer for my new pool project. The job includes: Install approximately 10 metres of frameless glass pool fencing Install 1 glass pool gate (self-closing and compliant with pool safety requirements) Install approximately 11 metres of aluminium pool fencing The materials may be supplied by me, or I’m happy to discuss supply and installation options. Looking for someone experienced with pool fencing installation and ensuring the final installation meets Queensland pool safety standards. Please provide your quote, availability, and any relevant experience/photos of previous work.

L shape pool fencing to be installed. 8.05m of glass fencing including a soft close gate attached to the wall 5.6m of aluminium fencing 8 x base plated spigots 4 x posts with base plate All materials provided, except for tools. We are looking for someone who is experienced in poo fencing.

I have been given a non compliant pool fence notice . There are various repairs including - sections around gate where fence is 5mm too short. Possible packers needed under posts. - some retaining structures are too close, possibly replace fence panel with taller panel or use Perspex shield - gate and latch adjustments

Remove old pool fencing We want to keep the concrete and not damage so that we can tile and install new fencing. Remove from property 3 sides approx 6m, 10m, 10m

Aluminium Pool fencing to be elected around pool and garden edge .

Need someone to hang x2 protector gates.

I need a glass pool fence and glass gate installed on an existing level concrete plinth. The total length is 3.45m between a colourbond fence and house rendered wall.

Need pool fencing installation for a 8x4.4m size pool, either glass/ aluminium

I am looking for someone to install swimming pool fence approximately 14.4 metres asap.

Please can you quote me to install glass fencing around the pool. 9.57m along the long side and 5.9m across the short side. The are to the right on the short side needs some concrete between the pool and the wooden garden fence.

He have to replace pool fencing. Looking at Bunnings aluminium options and also True Batten - if anyone has experience in installing this? Also need to install some perspex, replace latches and hinges

We have an existing glass pool fence that requires repair. The stainless steel spigots are in good condition, however the anchor fixings have rusted and need to be replaced. Note that each glass panel will need to be removed to access the bracket fixing points (2 person lift that I can assist with).

Hoping someone can come with a grinder to help cut pool fence (removed) spigot. Happy for it to be completely removed as well, whatever is easier. Thanks.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.

I’m putting up a pool fence in peregian Springs . I could use a bit of help lifting and setting the glass panels. Thanks,
Phil

I want to get a new compliance certificate for my pool in Benowa but need to get a few items fixed first. - One panel to replace (now lower than new concrete) - Gate adjustment - out about 15-20mm - Gate adjustment - a few mm (it is an adjustable one) - 4 panels to raise (about 20mm) - 1 panel to fasten to one side of top of post - Cement in 3 click clack bricks - Replace one gate latch