Find a local glass fencing contractor in QLD

Repairs required to rusty pool fence

I am looking to get fully complaint glass fence done on two sides of my pool. One side measures 11.6 m and other side is 6.4 m so approx 18 LM. One self closing gate on each side

The pool glass door is not shutting properly. Need to check and fix the issue.

I need someone to assist in anchoring a pool fence to make it compliant.

Pool fence certificate requires end panel to be fitted to post top and bottom, has come out

Install Glass Pool Fence Looking for an experienced glass pool fencing installer to install approximately 6.3m of glass fencing/gate, either end of pool as per picture. * Existing aluminium fence will be removed prior to installation. * We already have the glass panels/gate/spigots. * The spigots will need to be drilled into porcelain tiles, so experience drilling and securing into porcelain is essential. * Must have experience installing glass pool fencing.

Supply and install 1.2m high aluminium pool-style fencing along both sides of the waterfront walkway, as marked in red in the photos. The old fence in the photo has been removed. Each side is approximately 2 metres long — around 4 metres total. Fence should be securely fixed to the existing timber deck The first section is 78cm, then change direction, 2m in total on one side, then another 2m on the other side.

1 section requires replacing and the gate has come off the hinges. Locking mechanism has also fallen off

Rectify issues identified in pool safety inspection and install a new metal pool fence of approximately 5m (please see attached photos). Not sure of cost and so tentatively set a budget of $1000.

I need a glass gate constructed similar to a pool fence style approximately 1 metre wide

Installation of around 35 metres of aluminium fence and timber posts. These are supplied along with brackets.

Hi my pool glass gate needs adjusting as it doesn’t close within the lock as the glass is out of alignment

Erect glass panel pool fence on 2 sides of pergola. Have glass panels already

Glass panels are all slowly coming undone and wonkey as ground has moved and posts done align with glass any more. I have had a few panels done with additional spigot support but I want the lot done now: removing the posts and replace with spigots. 10-12 panels need spigots, depending on what’s possible on either end (might need to leave some posts in, especially with the door): I have sourced spigots already. Scope of task: - assess and recommend best way forward with the end and door panels - remove and replace posts with spigots: 10-12 panels - supply tools: to drill holes into tiles without wrecking them - other bits and bobs needed: bolts etc - remove posts from premises: dump run etc Location is Ipswich central. Thanks Oliver Edit: I just realized I did not adjust the budget since I had this task online last time given I have now sourced spigots already and they’re not included in task any more.

We have purchased a house (20yr old) that council has failed for pool compliance. It has a servery window which bi-folds back and once opened stacks approx 40cms from the pool fence. So is deemed as climbable and non compliant. We require a 600h x 800l x 12mm thick clear Perspex and o be attached to the house & top of glass fencing temporarily for compliance. Needs to be done by Friday 5pm

I have been given a non compliant pool fence notice . There are various repairs including - sections around gate where fence is 5mm too short. Possible packers needed under posts. - some retaining structures are too close, possibly replace fence panel with taller panel or use Perspex shield - gate and latch adjustments

Please can you quote me to install glass fencing around the pool. 9.57m along the long side and 5.9m across the short side. The are to the right on the short side needs some concrete between the pool and the wooden garden fence.

We have an existing glass pool fence that requires repair. The stainless steel spigots are in good condition, however the anchor fixings have rusted and need to be replaced. Note that each glass panel will need to be removed to access the bracket fixing points (2 person lift that I can assist with).

Hoping someone can come with a grinder to help cut pool fence (removed) spigot. Happy for it to be completely removed as well, whatever is easier. Thanks.

Install aluminium balustrade inc. collection from Bunnings We need someone to collect and install an aluminium balustrade. Materials purchased by us upfront — you will not be out of pocket at any point. What you need to do: - Collect ProtectorAl aluminium fencing components from Bunnings (we will purchase and arrange) - Install on site: 2800mm straight run + 1000mm return at 90°, mounted to top of masonry wall (approx measurements). - 4 flanged posts dynabolted to masonry, 3 panel sections (2 panels cut to size between pickets) Tools required: hammer drill + 10mm masonry bit, angle grinder or hacksaw for cutting aluminium, level, basic hand tools. Materials: Purchased by us upfront Please check the photos before quoting.