Find a local brick fencing contractor in Inner South Melbourne

PLEAEE SEE ATTACHED PHOTOS Cut and remove 2 sections of brick fence to allow vehicle crossover to connect to driveways. There are two sections of the fence to be cut and remove as follows: 1. Section 1 is half removed. You will remove the rest of the marked section then construct a brick pier on either side of the removed section of the fence. 2. Section 2 of the brick fence is very low. Remove the marked section of this fence. Then construct a brick pier on either side of the removed fence. You will bring and use your own equipment. The site must be cleaned up after you are done. Please quote only for the entire job and no hourly rate offer.

Brick fence post/pillar in need of repair knocked over by our car. Move original position across slightly to enlarge driveway opening to reduce chance of future damage happening again if possible. The brick pillar has been repaired before and appears to be repaired with cement (rather than mortar) so unsure if old bricks can be reused. But maybe the original pillar can be lifted into place without breaking up the pillar? But it is heavy so could not be lifted by hand. Note the pillar is now lying on the ground. Differing from the photo I have posted.

As before - brick fence to be built in Black Rock

Looking for an experienced bricklayer or fencing contractor for two jobs on my front brick fence: Cut a section out of the existing brick fence to create an opening for a pedestrian gate (gate not included – happy to discuss whether you can supply/install one, or I'll source separately). Fill in a gap at the end of the fence to match the existing brickwork. Looking for a clean, tidy finish that matches the existing brick and mortar as closely as possible. Please include: Relevant experience with brick fencing/gate installations Whether you can supply and hang the gate, or just prepare the opening Estimated timeframe and cost

Build a brick fence. Footing will already be in place. Piers need to be core filled.

We had someone damage our short brick fence and two front pillars, we need this replaced and fixed, with same bricks to match rest of fence.

About 10m length brick wall fence footing -concrete job

Looking for an experienced bricklayer / concreter to demolish and rebuild 2 x structural brick fence piers to a specified brief. Scope of works: Knock down and remove 2 existing brick piers Excavate and construct 2 new reinforced concrete footings. Rebuild brick piers and core-fill as specified Pier dimensions (each): 1500 mm high 360 × 360 mm Footings (each): 800 mm deep Pad size to suit pier (approx. 600–700 square) Concrete: N20–N25 Reinforcement: Reinforced footing cage, N12 deformed bar, 4 vertical bars, N12 closed ties @ ~200 mm centres, Minimum 50 mm concrete cover Steel posts: 1 × 100 × 100 × 4 mm galvanised SHS per pier. Post embedded 600–700 mm into footing. Post tied into reinforcement cage. Posts must be plumb and set before concrete pour. Pier construction: Brick piers built around steel post. Core backfilled with N20–N25 concrete. Brickwork tied to steel post. Piers to be square, plumb and ready for future gate automation Important: Structural steel carries gate loads — brickwork is non-structural. One monolithic concrete pour per footing. No dynabolting or post-install chemical anchors Access: Good Start: ASAP

Replace metal edging and render brick fence ready for painting

The corner of the brick fence 2m high was damaged (see the photo). Metal angle and the render is to be reinstated and then painted in monument colour as the rest of the fence.

A part of the fence including the postbox was damaged, which needs to be reconstructed. Pics attached.

I have 4 L self priming white paint and a roller suitable for brick as well as some paint brushes. Just need someone to brush the surface clean and then paint. Front wall is 10.5mx1.85m, side wall 9mx1.85m and photo is of a third wall just needing some spots touched up.

We are wanting a 9.86 meter by 59cm brick front fence demolished and removed.

We have no front fence and want a brick fence to match same used on the house. Its roughly 15m length would like a brink fence built. Will need to level grass. Flexible with date

To build up brick fence with 3 x columns 1.2m high. Total distance: 5m. Fence and columns will be rendered, so the brickwork look doesn't matter.

The brick fence between me and my neighbours property has cracked and is leaning about half way up. There is a vine that is growing on it, which could have caused the issue? Need someone to secure the brick fence or quote on removing.

I have a brick fence with 4 timber panels. The brick has recently been rendered, and now the panels need to be reattached to the brick posts. Each panel needs to be secured with 2 screws on each side (4 screws per panel) into the brick posts. What’s required: * Drill suitable for brick * Screws and wall plugs * Experience with fence or basic handyman work Should be a quick job for someone with the right tools.

Need supply and install of brick fence in the backyard. There is an existing brick fence so this new bricks need to be installed in continuation to the existing bricks fence. See photos for reference.

Section of the front brick fence collapse , need fix

Hi there. Finishing up a new home for a client in Highett and need the new brick front fence rendered. It’s being built now, ready in 2 weeks. 18m long. 1.8m high. 9 piers (on the inside only). Render both sides. Total render approx 65 square meters. I need a price for black colour acrylic render. Please include ex angles to all piers, wall ends and top. Cheers. Julian.