Find a local electronics repairer in North East Melbourne

I’m needing the washers fixed on my bathroom taps, you will need to come work out what to buy from Bunnings (5-10 mins drive away) or if you have the washers and fix

Looking to remove three hedge trees and stumps. I can keep mulch

I have an old tap which I need moved (as it is too low) about 50cm from where it is on a little pole, to the larger pole that holds the hose reel. I also want the height increased so I can fit tap timer etc under the tap and connect a hose, plus I want 2 taps instead of one. Will need to supply parts including 2 quality brass garden taps. Must be a qualified plumber and able to work with copper pipes and brass fittings etc. Please refer pictures and feel free to ask questions.

Need caps installed on 6 brick piers. Need to have done this before, not looking for handy persons. I will supply all materials including assisting with lifting up the caps.

I am looking for a licensed plumber to adjust the location of water taps in the laundry.

Front steps and porch need tiles Will provide rough measurements of the area I will supply the tiles

Quick stump grind of 3 fresh 9 inch diameter tree stumps. Easy access from road across front lawn to garden bed in front of home

My simpson oven isn’t heating up . The grill underneath is still in working I’m assuming it could be the thermostat

Hello, I need my new king bed frame + 2 king size mattresses to be taken upstairs and assemble it. Photos attached of bed frame. Not sure of box dimensions, but can be opened downstairs and carried up in parts if required. Photos of stairs attached. I also have a side balcony that goes straight to my room if necessary. Preferably in the late afternoon after 2:30pm. Put in your offers please

When flushed the cistern fills to tube then water runs into tube and doesnt stop

Install taps. - View all the details of this offer: https://www.airtasker.com/offers/01KATVM7EXRCCRX3TW0SCCG33B

Hi there! We just need someone to come and fix a couple taps and tighten up some loose fittings. Here’s a list: - Bathroom sink tap, it seems the mesh as come out of the tap so it’s spraying water. - Shower tap, the handle itself has come off - Soap holder, is just loose and needs tightening so it doesn’t flip - Toilet roll holder, also just loose and needs tightening I’ve attached photos of all of the above! Just let me know if you have any questions :) Also just an FYI that we have a dog, she’s super friendly and we’ll keep her out of your way, but she might come and say hello so I’d you’re not a dog person just something to keep in mind!

A few paint chips on a wall, and a windowsill need patching before I vacate my rental

Change the tap in the kitchen to a retractable dual spray mixer. Change 2 bathroom taps and mixers. (3 sets) Change the bath sets. All have been purchased.

Fix 2 taps which are shaky 1. Washbasin tap (this might need moving the basin and do it or even put a new one (I will have a new tap stand by)- see pics ) 2. Sink tap - this might be an easy one - It just keep shaking even after I fix it with my hand. So just need a good fix so that it doesn’t keep shaking

Collapsed fence at rear of property needing replacing. Looking for standard no-frills 1.8m tall paling fence. Approximately 8.7m in length. Feel free to quote for building of new fence, removal and disposal of collapsed fence, or both. Already have agreement with adjoining neighbour.

Needs to paint a patch on a wall that has been painted but with a wrong white paint. Need to paint that and few touch ups trough out the apartment for a rental property.

There was a hedge that has been removed, but the stumps are still in place and need to be ground down. There are seven small stumps in total. Stumps with small limbs will be cut back so only the stump remains for removal. When: Needs to be completed before Monday.

Trim Laminate benchtops, one sink cutout and join prep for two straight corners (routing recesses) required. Trimming - There are 3 benchtops 1. Trim 246 cm benchtop to 240 cm and cut sink opening. 2. Trim another 246 cm benchtop into two sections (~75 cm and ~130 cm). 3. Trim a few cms either side of 240 cm benchtop (cut a few cm off each end to remove damage sustained in transit). Cut one sink opening Prep straight corners - router underside recesses for connector bolts. Please quote price - also happy for you to quote second quote for install onto cabinets - existing cabinets - all level.

My gas hot water system Dux Prodigy ignition/pilot light keeps turning off and won’t stay lit. I managed to follow instructions and the flame stayed on for 2hrs and now the flame won't light up when following the instructions.