Find a local electronics repairer in Heidelberg

Hi! I'm wrapping up my move out of this apatment and I just need someone handy to do the following: - Wall & Surface Touch-ups: Removing scuff marks (wardrobe, living room) and filling/patching a shallow linear wall dent where furniture sat - Hardware & Minor Fixes: Re-attaching a loose door hook - Laundry Detail: Treating some marks (?from washing liquid) in the laundry sink. Please see attached photos for the described blemishes

Remove laundry taps. Cut existing pipes shorter. Permanently seal pipes so can be concealed in wall cavity. I will patch the plasterboard. I will dispose of waste materials. I will clean up. Must be licensed and provide warranty for work. See photos with approx measurements. Must be able to do the job so that the hole does not effect the existing bench top and can be covered by new splash back (height shown in photo).

I need an experienced painter to paint the upstairs corridor and stairwell of my home. All surfaces to receive 1 coat of primer followed by 2 coats of Dulux white (3 coats total). All paint — including primer — will be supplied by us. Scope includes prep, masking, and full clean-up on completion. Timing is flexible; happy to work around your schedule. Requirements: >1 coat primer + 2 coats Dulux white throughout (walls, ceiling, trims) — all paint supplied by owner >Surface preparation included (fill, sand, spot prime as needed) >All masking and drop sheets supplied by tasker >Neat cut-in to all edges, no overspray/spillage onto timber floors or balustrade >Tasker to supply own ladders and access equipment >Full clean-up on completion >Must be able to work safely around staircase and balustrade

House built in 1994. Bath tub upstairs. Seperate handle and same spout. Hot water not working. Have tried to replace spindle although not exactly the same. Does not seem to be damaged anyway. When I’ve had it off and turned mains back on there is the slightly amount of water coming out of the hot side. When I turn the cold water on it comes out of the spout and out of the hot side opening. Additionally some older style taps are leaking

I have a vintage Tobisha record player that was restored by open ear studio a few years ago and I have 2 custom built passive speakers. I had a friend look at a distortion issue I was having and he unwound and then rewound the wires to try to get a better connection but when he reconnected them it lost all signal to the speakers i.e. wasn't making that typical 'buzz' noise that shows there is a connection. There is now no sound at all through the speakers. I honestly don't have any idea about this type of thing and I don't know if this is a wire issue, a speaker issue or an amp issue. I have a preference if someone could come to my place to have a look for diagnostics.

Need some taps connected to the bathroom and kitchen the taps are already supplied

Removal of two yakka stumps. The second one in the photo will be cut down to just above ground height

Supply and repair broken section of stone wall and replace cracked stair.

Looking to get 2 Focal K2 6.5” speakers repaired. The speaker terminals have been pulled off the voice coil and will need repaired back on. One speaker has the terminals there but not connected to the voice coil, and the other speaker will need new terminals put on. Thanks

this is the circuit board for a Honda Accord G9 ABS module as you can see from the picture and number of the wires connecting the circuit board to the pins around the edge of the picture have become either dislodged or lost completely. missing wires needs to be replaced and the loose wires need to be resolded. there is nothing wrong with the electronics of the circuit board it is just the connectors that need repair.

Need to remove carpet tack strips from 3x4 metre room - needs to be done without damaging floor boards - quick and easy job if you have the right tools (I don’t)

I am after a quote to install some speakers and an amplifier. They are pioneer 6.5” component speakers. I am wanting them installed into my Toyota Prado 2014 model. Thanks also what are your availabilities to please.

I hope to find a handyman who’s done this before! I’ve upgraded my racing rig, however the holes to secure the direct drive steering wheel is not compatible with the metal plate that the racing rig has. It seems that what is required is additional holes drilled in order to secure it tightly. While you’re here, I might get some advice on how to secure the pedals too! Steering wheel and pedals - PXN V12 Lite Rig - Playseat Formula In specific detail: 1. Drill probably 4 holes on the rack itself 2. Need 4 compatible screws for this - the ones provided are really small 3. Help to secure the pedals (similar situation as above)

Need someone to come to Heidelberg and jumpstart a car, but need to bring cables and a ?battery

Please just come and jumpstart my car! You need to bring cables to jumpstart the car! A quick 5 minute job!

The table I want is too big to fit through door, needs to be unscrewed and brought inside then screw back together. Heidelberg 😊

L2 trigger on my scuf controller (instant triggers) is faulty and sometimes unresponsive, looking to get this fixed

1. replace a kitchen tap with a new one ( new tap will be provided ). 2. Bathroom tap ( 2 off) to be fitted properly - Due date: Before Saturday, 16 December 2023

Steps 5 and 6 needed doing on a captain snooze BE-6XX Series Gas lift bed. Photos are included. This is a job with 8 screws only. - Due date: Needs to be done on Friday, 13 October 2023

Need someone to go to the property and give us a quote for repairs needed. - Due date: Flexible