Find a sockets and switches installation professional in NSW

I’m looking for a licensed electrician to install a couple of new wall power sockets and tidy up some existing messy wiring. I’m after someone who takes pride in their work and can deliver a very neat, clean, and professional finish. Please only get in touch if you’re experienced and have attention to detail.

Walls are being constructed and opened not sheeted yet , need someone to rough in wiring and fit switches to sheeting when done this week coming

Hi, I need a qualified/licensed electrician to convert 20 hardwired LED downlight drivers to surface sockets in my property. Job details: Disconnect 20x existing hardwired LED downlight drivers from 240V ceiling wiring. Install 20x Ceiling Surface Sockets (413 plug bases). Connect/plug the LED drivers back so all lights work. Access is easy through existing 90mm downlight cutouts. Materials: All 20x Surface Sockets supplied by me. Labour only required. Requirements: Must be a fully licensed electrician. Thanks!

I just need to replace five old wall light switch with the budget of $150. Please contact me if you hold a electrician license near Liverpool area.

Removal of plug sockets from the wood panel, replacing them into the plywood wall, potential fix to the wall

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Need some cables running in kitchen for new power sockets On the image, the Red is existing power The left hand corner is where the mains power for the cooker is which will need running behind to where the new cooker placement is going. I’ll need power new slot which is the green section and there is another PowerPoint below at the bottom of the kitchen the back which will be used for the cooktop but currently doesn’t seem to be given off any power.

Three bedrooms in our home previously had ceiling fans installed. The fan speed controller has been wired correctly; however, the bedroom light switches were not rewired from the original wall switch to the new switch on the fan controller. I’m looking for a licensed electrician to rewire the lighting in all three bedrooms so the light is controlled from the new fan/light switch panel instead of the old switch. Each room has the same setup, so it should be the same job repeated three times. The successful Airtasker must be a licensed electrician and hold appropriate insurance. Please include your licence details when making an offer.

I'm looking to add 2-3 power sockets along the wall in the photo towards the bottom. Currently the only power points are next to the antenna and ethernet point. All these are behind the frame on the wall in the attached photo.

Screw in 3 light switches 1 power point 1 light

To replace 4 Double Power Points, as they have stopped working. I can provide the replacement parts, and the task is only for labour cost.

I need a Qualified Electrician to provide and install 3 light in my flats and fixed one light switch please. You need to provide tax receipt or invoices. Photo attached

Looking for an electrician to complete a small residential job in my apartment. The apartment was built around 2000, so the wiring is relatively modern and I don’t anticipate any major issues. Work required: Light switches and power points + two LED lights replaced, includes - * Replace 11 × double power points * Replace 1 × quad power point * Replace 6 × single light switches * Replace 1 × two gang light switch * Install 2 × two gang LED dimmer/switch combinations * Might need 1 × surface mounting block (bathroom) * Install 2 × new Martec Fino LED ceiling lights, replacing two existing LED ceiling lights (same locations, pretty much the same lights just a bit bigger, no new wiring required ect) I will supply everything, it’s Clipsal Iconic and I think the old ones are HMP: * Clipsal Iconic switches and power points * Martec Fino LED lights * Dimmers * Mounting block I’m looking for: * Licensed and insured electrician * Neat, professional installation * Experience installing Clipsal Iconic products and LED dimmers Preferred, not necessary though Photos of the existing switches, power points and lights can be provided if needed

Need a licensed electrician in Sydney to adjust wiring for ceiling fan/light switches. Currently there are two switches: 1. Low light 2. Main light + ceiling fan together I’d like it changed so that the fan is linked to the low light instead. Main light still needs to work properly. Please quote including callout/labour.

Need qualified Electrician to: 2 x replace existing 4 gang mechanical switch to new 4 gang smart switches 2 x replace existing 6 gang mechanical switch to new 4 gang smart switches 1 x replace existing 3 gang mechanical switch to new 4 gang smart switches 1 x replace existing 1 gang mechanical switch to new 2 gang smart switches 2 x replace existing 2 gang mechanical switch to new 2 gang smart switches 7 x replace existing 1 gang mechanical switch to new 1 gang smart switches Switches I have purchased: https://amzn.asia/d/0eCM9VSb https://amzn.asia/d/0dQzODls https://amzn.asia/d/0gJdQbvq Install a recessed plug - to mount a magnetic plate for iPad as per: https://community.home-assistant.io/t/floating-ipad-dashboard-wall-mount-that-is-charging-magnetic-and-detachable/956322 I have purchased: https://kuxiu.co/products/kuxiu-x39-pro-max?variant=46232839356468 and looking to mount.

Needing a certified electrician to replace: - 12 x double power-points - 1 x single power-point - 1 x 2 gang light switch (light + bathroom fan) - 1 slim light switch - 1 regular light switch We will provide the hardware. We just need someone to do the work (with their own tools). We are available most days any time. Power points and lights work, we just want to update them with new switches. Happy to pay cash

We have repainted our house and we need the below installed: - light switches (replace old ones with new ones) - powerpoints (replace old ones with new ones, add a couple of new ones) - downlights (install new lights in lounge, dining, bedrooms and a couple of other places, ie, hallway, etc) - exhaust fan in bathroom - light on front porch (replace existing light) The property is a small three bedroom house. We will cover the cost of the equipment, ie, lights, switches, etc, or go to Bunnings and get it. We would like to pay for labour ideally between $60 - $90 per hour. Estimate there is around 10 hours worth of work.

I have 15 light switches and 15 PowerPoints (double) that need updating. Not installing any new ones, just replacing what I currently have with new Clipsal ones. I will supply materials (light switch and PowerPoint). Just need install cost.

I'm needing someone to supply and replace two bathroom light switches in an office building with more modern ones. One of the light switches has become "stuck" and cannot be pressed on, so the light in the bathroom cannot turn on. The other light seems to be working fine, but I would prefer both to be replaced regardless with a more modern switch You will need to supply the new light switches, and ensure both are working. Please let me know if your quote includes the materials, or if you will provide a receipt upon purchase and I will reimburse separately. Must be done on or before Wednesday 6th May Thank you

We need two light switches moved from their current location on the wall to another area of the wall, about 30 cms over. The light switches are near door ways and we are widening two doorways and need to move the switches over to allow for the widening.