Find a local Tasker to help you make a kitchen cabinet in VIC

Laminate kitchen cabinets. Top cabinets - timber Bottom cabinets- white Pantry - black

Re-level of kitchen cabinets

I need my kitchen cabinet door (only one door) and some interior panelling reinstalled. No need to supply parts (maybe fasteners only) - I have the cabinets that were removed with me

Our fridge is larger than the allocated fridge space in the kitchen. An additional 30cm of width is required for the fridge to fit properly. To achieve this, the upper and lower cabinets on the left side of the fridge space will need to be adjusted, along with the benchtop and the kitchen backsplash. A wine cabinet needs to be added next to the fridge cabinet to fill the additional gap created. This work will involve cutting and modifying the existing cabinets, doors, benchtop, and kitchen backsplash, along with any associated tasks and touch-ups required to achieve a clean and neat and professional finish. Size of the benchtop: 160cm (length) x 70cm (depth)

We have replaced our wall oven with a smaller one and need the hole filled in with another draw and joinery

I would like the current sliding bench top in my vintage caravan cooking area to be raised by 10cm to allow room to fit my air fryer into the cabinet

1) Remove old kitchen bench, draws and cupboards. 2) Build and install IKEA kitchen draws, cupboard, dishwasher alcove 3) Cut sink hole and fit into benchtop 4) Drill hole for mixer tap and fit to bench top

I need an existing dishwasher removed and cabinetry repaired or replaced. I also need have a couple of drawers that need the soft close hinge replaced as well as a pocket door hinge replaced.

I will be available all morning tomorrow for an appointment to view the property and work necessary for quote Had to buy a fridge as the old one finally failed. New didn’t fit into the fridge cavity of our built in cabinets. I took out and replaced the floor with a thinner board. Reassembled and complete screwed it up. Need inspection and then estimate to fully repair Estimate given here purely a guess.

Make kitchen cabinets level. Budget is $100.

Recently completed a kitchen renovation with new shaker-style cabinet doors installed. Looking for someone experienced with kitchen cabinetry or joinery to fine tune the alignment on two small overhead cabinets (4 doors total — two side-by-side cabinets with two doors on each). A few of the door reveals/gaps are slightly uneven (approximately 1–2mm) and I’d like them adjusted for a cleaner, more consistent finish. Likely a straightforward hinge adjustment job. Photos attached.

I would need a kitchen cabinet built. Its new and all the instructions will be in the instruction manual.

need assistance for 30min to help hold joinery in place while I screw it to the kitchen wall above rangehood.

Please note: Work required in MAY. I am undertaking a renovation and the Kitchen cabinetary is being reused at another house. The job is to carefully defit the cabinets so they are preserved for refit. There is: 1 x Island with 2 x 3 drawers, wooden benchtop needs to be cut at the edge of the drawers as it wraps around a corner 2 x Floor cabinets with 3 drawers - wooden benchtop to be kept 2 x Glass fronted overhead cabinets

Cabinetry requires some changes to accommodate replacement dishwasher. Likely lower bottom shelf by 5 mm and amend drawer face to align.

Current cavity for oven is about 1170mm high and we are replacing with new oven that’s around 890mm high. Want a filler panel and shelf for bottom of cavity to make sure oven appears snug in cavity. White gloss melamine finish for filler panel.

We have some new soft close hinges to go on 9 refreshed cabinet doors. Would like them to line up etc. Have hinges and tools. Just need someone who may have done this before. Is good at measuring accurately and drilling. Photo of old hinge, then of new hinge.

We need the open cabinets on either side of the range hood removed as they no longer fit with regulations for the height of the stovetop. The cupboard above the range hood can stay. The house is 1980s so I’m not exactly sure how they are secured. We would then like replacement shelves or cupboards that don’t go lower than the range hood installed - happy to buy these separately for you to install if that helps.

Need extra space to fit in a larger space in kitchen. Fridge is taller and wider than the current space

Hi, I am looking for someone with the right tools (specifically a powerful hole saw) to drill a clean hole through the internal panel between two kitchen cabinets. The purpose is to feed a cable from a microwave drawer through to the under-sink area. Access is straightforward, but the cabinetry is quite solid so I need someone experienced who can ensure a neat finish without damaging the surrounding panels. Please bring your own tools and be confident working with kitchen cabinetry. Happy to provide photos and measurements if needed. Thanks!