Find experienced local carpenters in Adelaide

Remove existing MDF. Close a niche with appropriate timber and a Window before waterproofing for tilling a bathroom

I need this freezer to fit neatly underneath my cabinet - shelf and bottom need to be cut back .

Timber around the door handle and lock has broken away and needs to be repaired/reinforced. Looking for someone experienced with carpentry/door repairs to: * Repair/rebuild the damaged timber around the handle and lock area * Reinforce the area so the lock and handle are securely mounted * Refit the existing handle/lock hardware if it is still usable * Make sure the door opens, closes and locks properly * Finish the repaired area neatly, including filling/sanding as required Would prefer to repair the existing door rather than replace it if possible. Photos attached showing the damage and existing hardware.

Hey! Looking for a carpenter or cabinet maker to install a second-hand kitchen at my place.Must have solid experience putting cabinets together and fitting them properly.Drop me a message if you’re interested and want me to send over some photos!

replace spiral balance in a timber frame single hung window. Spiral balance/ window height 880mm in height, width 1150mm.

Looking for an experienced cabinet installer / carpenter to install flat-pack kitchen, laundry, and wardrobe cabinets from supplied manufacturer drawings (KLF cabinetry, Hettich hardware). Scope: - Kitchen: base cabinets (~2.4m + 3.0m runs) + overhead cabinets, including sink cabinet, dishwasher housing, oven housing, rangehood cabinet Cabinets are pre-fabricated flat-pack (need assembly + installation + levelling + scribing to walls). Hettidesign soft-close hinges and drawer runners included. Not required: benchtop install, plumbing/electrical connections, splashback (will arrange separately with licensed trades). Please provide: - Hourly rate or fixed quote - Estimated time to complete - Confirmation of experience with flat-pack cabinet assembly/installation

Searching for builder/carpenter Proof of insurance required 4-6week project Nov-Dec Varied works Shed demolition Renovation Assist with civil Prepare property for sale Inc.general Labor $65-95 p/h

Hi, I’m looking for someone experienced to repair and restore existing kitchen and laundry cabinetry. Work required includes: * Repair damaged/chipped cabinet panels, trims and edges * Prepare and repaint existing cabinet doors/panels * Repair damaged timber benchtop areas * Sand and refinish/recoat timber benchtop as required * Make good any minor damaged areas around the cabinetry * Match the existing white cabinet finish and timber colour as closely as possible The intention is to restore the existing kitchen and laundry, not replace the cabinetry. Photos will be attached showing the current condition. Looking for someone with cabinetmaking/joinery or kitchen restoration experience who can provide a neat professional finish. 📍 Adelaide 📅 Ideally completed before the end of August Please let me know your availability, experience with similar work, and whether your offer includes materials.

I have an active insurance claim but they won’t fix internal damage u til I fix externals. Outside my wheelhouse, so need help. Small section of rear corner of eaves is damaged and needs replacing/repair. Will require some timber (probably less than 1m) and some eave cladding (1 sheet - I assume?). I can paint myself later. Photos attached. Feel free to ask questions or drop in to inspect. Because of sloping block roof access is easy ( can just walk on). Also have rear yard access from back street.

Needing someone to put a (very small) ikea kitchen put together and installed. The room is 2.5 x 2.8m and includes the below: 4 X lower 600mmW cabinets 4 X upper 600mmW cabinets 1x 600mmW cabinet (2mH) 1 × 450mmW tall cabinet (2mH) - integrated fridge - integrated dishwasher - integrated exhaust

Small stain in white kitchen benchtop. Need stain removed, polish and resealing

2 x new door frames plus a non-structural wall, plastering, trim and skirting board

This lid contains heat resistant bricks and metal strip to hold it. It opens up because the metal strip around the side has corroded and collapsed. The lid’s rim needs to be reinforced so it can hold its shape and remain securely in place.

Looking for an experienced cabinet maker/joiner to build and install a modern mudroom and shoe storage unit in my garage. I’ve attached a concept image for inspiration. It doesn’t need to be identical, but I’m after the same clean, built-in look. Dimensions * 4000mm wide * 2450mm high (2500mm ceiling) * 400mm deep Requirements * Two full-height shoe towers (approx. 800mm each) * Central bench (approx. 2400mm) * Oak-look timber slat wall behind bench * Four family sections with hooks (Luke, Lou, Myles & Felix) * Overhead cupboards above bench * Open shoe storage under bench * Soft-close drawers and doors * Storage for approximately 80 pairs of shoes Preferred Materials * Matte black melamine cabinetry (or similar) * Oak-look benchtop * Oak-look slat wall * Black handles/hooks * Warm white LED strip lighting (optional) Happy to discuss alternative materials if they achieve a similar look at a lower cost. Please provide: * Approximate price * Timeframe * Photos of similar work (if available) * Any suggestions to improve the design while keeping it practical and cost-effective. Supply and install preferred, but I’m open to other options.

【Date & Availability】 Fridays or Saturdays ONLY (Owner will be home all day） ​【Budget】 $800 AUD (Base budget. Experienced carpenters with a proven portfolio are welcome to discuss a revised quote based on workmanship and finish quality.) 【Dimensions (L-shape)】 Main Bedhead Wall: 3.3m wide Right Side Wall: 2.07m wide Height: 2.6m 【Materials Provided】 9 x Oiled Walnut Slat Panels (300cm × 64cm) 1 x Matching Walnut End Trim (3m) 1 x LED Strip Kit (4 strips + transformer) 1 x Clip-on peg shelf 【Scope of Work】 Cut panels from 3m to 2.6m using a track saw to prevent veneer damage. Precise cut-outs for 2 x double GPOs (flush finish required). Conceal low-voltage LED wiring behind panels before installation. Install panels with accurate vertical alignment and clean L-corner joint. Cut and install end trim on exposed edge (260cm). 【Requirements】 Must have professional tools (track saw, laser level, etc.). Please include photos of previous timber slat wall / feature wall projects. Careful handling of premium timber veneer materials. Clean and tidy workmanship required.

Kitchen cabinet door hinges needs adjusting. Nothing is broken, just hinge adjustment so the doors can close properly

4 Timbers need to be screwed on the back (each as, just follow the instructions), and 2 vents need to be swapped around on most the inside (3 screws in each vent). All material and screws are there

I Need to install the door I will be home during the day today or tomorrow and I can help to hold the door if needed. Send your offer please

I have an L shaped cupboard door thats come off, the bottom screws have snapped into the wall I just need the door back on I'm not fussed if the screws are removed or if you just put them in next to it. As long as its functional as it gets opened and closed hundreds of times a day. Otherwise if you can just put the holes in for the new screws I can reattach it myself, I just dont have the tools I need to drill the holes or remove the screws.