Find local bathroom renovation experts in Inner South Melbourne

Two sections of silicone/sealant in our tiled shower have failed — one longer strip has pulled away from an internal vertical corner and there is a smaller failed section at a tile/corner junction. Looking for someone experienced with shower resealing/caulking or bathroom tiling to: - Remove the failed/old silicone properly rather than silicone over it - Clean and prepare the joints, including any mould/residue - Inspect for any obvious signs of water penetration or waterproofing issues - Reseal the full affected internal corner/joints with quality mould-resistant sanitary silicone - Leave a neat, professionally finished bead - Advise if anything more substantial than resealing appears necessary Photos show the current condition. Availability: Wednesday 2 September or Wednesday 9 September, ideally between 11:00 am and 1:00 pm.

Reseal shower and one toilet. I have seal gun and white sealer but welcome to use your own tools

I’m looking for someone to remove the existing silicone from my shower and apply new mould-resistant bathroom silicone. The shower currently leaks from one corner during use, so I’m hoping resealing the internal / external edges will stop water escaping. The old silicone should be fully removed before new silicone is applied.

My shower has a minor leak and needs silicone and grout repair. The property is prone to ground movement so this will be the third time I’ve had it resealed. I’m hoping there’s a better method that can withstand the movement for a longer-lasting result. There is no surface leaking, so I’d like thermal imaging done at the end of the repairs to confirm the leak is fixed.

Need to fix the bathroom glass panel silicone sealant issues and some crack floor repair.

After someone to re-silicone the joints in my fully tiled shower. The old silicone has gone mouldy and stained and needs replacing properly. Scope: - Cut out and remove all old silicone: the vertical wall corners, the wall-to-floor join, and the glass screen base (both inside and outside, the outer join has mould too) - For the vertical corners, full height is likely overkill, so if cutting out just the affected sections is enough, that's fine - Once the old silicone's out, treat the exposed joints (bleach or mould remover is fine), then rinse - Degrease the joints with methylated spirits so the new silicone bonds cleanly - Let everything dry fully before resealing (fine to leave it overnight between strip and reseal) - Apply new mould-resistant silicone with a neat finish Details: - Fully tiled shower (ceramic floor and walls, glass screen), base roughly 90cm x 175cm - Must use premium anti-mould silicone such as Maxisil, Mapei, Soudal etc. - Photos attached

Old silicone in shower needs replacing. Light grey silicone required. Area should be treated with mould killer before new silicone is applied.

Looking to have shower re sealed. Requires re grouting and re sealing. Mould present under existing silicone and minor leaks coming from under the shower. 800x800x1800

There is mold under the shower glass and I need the seal to be replaced Type of clean: Regular Number of bedrooms: None Number of bathrooms: 1 Equipment and supplies: Tasker must provide

Bathtub has 2 short edges and 1 long edge which could do with re-silicone.

Description Looking for an experienced caulker or bathroom resealing specialist to fully remove and replace the silicone in my ensuite shower. Scope of work: • Shower base size: 1450mm × 850mm • Remove all existing silicone between the shower base and the floor cement sheet (2 sides) • Remove silicone/grout between the shower base and wall tiles (2 sides) • Clean all joins thoroughly (scraper + silicone remover) • Ensure surfaces are dry and prepped before resealing • Apply mould‑resistant, wet area, neutral cure, sanitary silicone with a clean, professional finish • Remove and replace silicone along the base and wall join of the frameless glass shower screen (1450mm fixed panel + 850mm fixed panel + door) with mould‑resistant, wet area, neutral cure, sanitary silicone with a clean, professional finish. • Current silicone has mould underneath. Important: • Must remove silicone back to clean substrate — not just skim over • Must have experience with bathroom/shower resealing • Please bring all tools and materials • Photos of previous silicone work appreciated Access: Standard ensuite, easy access. Parking available. Budget: Open to quotes around $200–$300 depending on experience and finish quality. When: Flexible

The silicone in my shower is mouldy and I need it removed and replaced with mould resistant silcone. Pictures attached.

Need shower grout cleaned and silicone for shower

Looking for help with the following: - Remove old, mouldy silicone from shower - Deep clean area to remove and prevent mould before resealing - Apply new water and mould resistant silicone - I can provide tile & grout sealer spray to finish the job Must have experience with bathroom silicone work. Thanks!

Remove existing sealant and re seal shower screen. Bottom only and approx 1200mm length

Regrout and silicone shower base

Moving in to a new unit, need shower resealed. Task: Remove the existing silicone and reseal with new silicone (base and wall joints). Need the job done tomorrow, Thursday the 16th. Cheers!

Some silcone is compromised and mouldy and needs replacing. Some grout needs deep clean to remove stains

The shower screen and door needs to be reattached and resealed to the floor, wall and ceiling. It'll first need to be removed and cleaned and then redone and aligned properly.

Remove old and mouldy silicone in the shower. Replace with new silicone to match tiles. Shower hasn’t been used in 6 weeks so dry. Can the job be complete Sunday 10th or Monday 11th November.