Find experienced auto electricians in Outer East Melbourne

Looking for an experienced auto electrician / 12V 4WD installer to complete the electrical setup in my 2016 Land Rover Discovery 4. I’m completing a custom touring/camping fitout and already have/planning the majority of the components. I need someone experienced to install and wire the system safely and neatly. The setup includes: KickAss 230Ah slimline lithium battery 40A DC-DC charger Roof-mounted solar panel Battery monitoring/shunt Fuse box, busbars and appropriate circuit protection Fridge + provision for future drawer freezer Starlink Mini 12V supply Sirocco fan 3 x USB-C/charging outlets Interior, rear and exterior LED lighting 12V water pump Provision/wiring for 12V hot-water system Switch panels/control points throughout vehicle Anderson outlets Provision/wiring for future 12V air conditioning The vehicle will have custom cabinetry, depending on timing and receiving this material the maybe completely empty inside or with cabinetry installed. Happy to assist with mounting, cable runs and other basic installation work myself if this helps reduce time/cost. Mainly looking for someone who can correctly design, size, wire, fuse, terminate and test the electrical system. Ideally looking for someone with experience in lithium 4WD/caravan systems, DC-DC charging and solar, and who can show examples of previous work. Located around Ringwood / eastern Melbourne. Time-sensitive: hoping to have the work completed ASAP as I leave for an extended road trip next week. Please let me know your experience, availability and an indication of labour cost. I can provide the full component list/layout before starting. Budget listed is an hourly rate starting point — happy to discuss based on the work required.

Looking for someone with some experience in vinyl wrapping to help wrap my car. I will be providing the vinyl wrap, so I’m mainly looking for someone with the skills, tools and experience to apply it properly. The car will need a full exterior wrap, and I’m happy to discuss the details, vehicle model and condition before the job. You don’t need to be a professional wrapping company, but please have some previous experience wrapping cars or automotive panels and be confident working with vinyl. Please let me know your experience and any photos of previous wrapping work if available.

Dash cam installation. Car Model : 2017 Outlander

Uhf installation into 2014 volkswagon amarok

Install New Car Audio Head Unit / Rewire Harness I’m looking for someone experienced with car audio to install a new touchscreen head unit in my car. The car previously had a single-DIN aftermarket stereo installed. I’ve now purchased a new touchscreen audio unit, which should be plug-and-play with the original factory harness, but the existing wiring needs to be rewired to suit the new head unit. Job includes: * Rewire/adapt the existing harness to suit to the new stereo * Make sure all functions are working correctly (power, speakers, etc.) I connected the wires by matching colours but it’s not getting power so Looking for someone with car audio installation experience who knows how to work with aftermarket head units and wiring harnesses. Car model - 2009 Mitsubishi lancer

Looking for someone experienced to professionally install a front and rear dash cam in a 2022 Mazda CX-5. Dash cam: Drivevision Installation required: Front + rear camera Power: Hardwired Hardwire kit: Supplied with the dash cam I’m looking for a clean installation with all wiring hidden behind the interior trim/headliner, with no loose or visible cables. The hardwire kit will need to be connected to the vehicle’s fuse box, ideally allowing the dash cam’s parking mode to operate correctly. Would prefer someone who has experience installing dash cams and working on Mazda CX-5s or similar vehicles. Please include in your offer: - Installation experience - Whether you have installed front/rear hardwired dash cams before - Whether you can configure/test parking mode - Any additional parts or fuse taps that may be required I will supply the Drive Vision dash cam and hardwire kit.

Have a canopy with central locking needing hooked up to car jut need wiring done

I have an old (but new in box) VIOFO A129 Plus Duo front and rear dashcam. I am looking to install this in a mg3 vibe hatchback (2026). I don't have a hardwired kit, do I need to purchase this as well for the install? Looking to have it installed after 26th August, would be flexible with time. Am in Ferntree Gully but could travel if required. Thankyou. The price I have entered in budget is just a rough amount, have looked at going price and have had huge varied estimates.

Remove hardwired dash cam from 2020 RAV4, then install hardwired into 2026 RAV4. Front & rear - Blackvue DR750X-2CH Plus

Hi I want to install Front Parking sensor and Front Camera in my mazda CX5 2024 soul red color. Car already has rear view camera and mazda connect display.Please provide quotes for both parts and installation,

Car stereo install. Replace single din unit with a new one we will buy. Car is a 2006 Hyundai Elantra

Install uhf radio into vehicle aerial as well . Ive had 2 different people booked in for this job and did not turn up . I require somebody to knows how to do this as require a professional neat job . Thankyou

Headlights don’t work, new bulbs required. Ford falcon BA2010

Need someone to install a car battery in my 2017 Kia Sportage. I already have a replacement battery from a wrecker, but I don’t have the tools to install it.

To install a pioneer head unit in a Mazda CX 9

I start installing apple CarPlay in N80 Hilux. Everything is connected because it’s plug n play unit with Hilux harness. However my rear camera is not engaging when it’s in reverse and steering control is not working. I need someone to plug n play wires and make it work. No need to put plastic back- I can do that. Unit is working except these two things someone needs to troubleshoot. Give me offers? Thanks

Hi, I’ve got a 2017 Mazda. I’m a crash repairer myself, and this Mazda was hit on the right side. I had to replace both blind spot sensors, which I took from another car. When I start the car, the sensors work fine for about 20 minutes—showing alerts on the mirror—but after that, they stop working and show an error. I’d like to know if you can calibrate them.

I have purchased the redtiger F7NP front and rear dashcam along with the hardwire set. Please quote me the hardwire installation cost for a Hyundai Tucson

Twin Gauge Installed wired thorough firewall 1x SAAS 52mm Oil Pressure 1x SAAS 52mm Water Temp 1x Twin Gauge Pod ( I don’t have automotive wiring)

Dash cam ventrue N4 Pro S installation on corolla hatchback