Find a professional gate installation in ACT

Please advise on specific gate and associated hardware materials required, for me to purchase, and then install these for me. Gate width is approx 1.5m and want it to be approx 1m high

Install an aluminum gate and aluminum posts. Posts are bolt on. Posts to be installed on existing concrete (see second picture) Please note posts will need to be cut down to size. Gate is welded and ready to hang. All hardware provided. Posts are 100mm x 100mm x 2m, and gate is approx 150cm x 150cm.

Kitchen Mixer tap body is loose, needs to be tightened against sink from underneath with correct tooling (a tube spanner). The dish washer is reported to not work, please investigate power and water supply and confirm functionality.

Install Feature fences in backyard There will be 7 slat fences with 13 in-ground posts. Fence sizes vary from 200 cms wide X 180 cms H to 200cmsX60cms. One double gate (100X150 each side) with a colorbond fence panel to close spaces between garage and brick wall. 4 in-ground posts for gate and colorbond fence. We will supply all fence and gate materials. Installer to bring concrete, do the 17 post holes digging, and provide all the installation related labour. The slat fences will come assembled. Supplier not finalised yet but one possible supplier is Alucom fyshwick, as per the following specs. GSGHD Glamascreen Slat Gate Fully Framed with 65x50 Rectangular Box Frame, incorporating 65x16 Aluminium Slats with Concealed Fixings, Stainless Steel Hinges & Double Sided Keyed Lock. All in Powdercoat Paint Finish. 1x Double gate. Each panel making size 942mm W x 1766mm H. 2x 65mm Above ground posts. QFSF Quik Fit Glamascreen Slat Fences Incorporating 65x16 Aluminium Slats with Concealed Fixings & Midrails where required. All in Powdercoat Paint Finish. 4x Fixed panels. Each panel making size 2000mm W x 1192mm H. 8 X 65mm posts 2400mm L. 1x Fixed panel making size 3000mm W x 1192mm H. 2x Fixed panels. Each panel making size 2000mm W x 600mm H. 4x Inground posts.

I need a quote to widen or replace existing gates. Either cut and refit further apart and add more to the centre or replace entire gates and swing a new lightweight single gate from the right hand post on the fence side. Overall width would be governed by re-aligning the house side post with the 1/2 wall. Open to alternate suggestions.

Need to replace the seals in tailgate of truck

Weld a large yard gate back onto its hinge

I will be getting approx 2.5 cubic metres of soil delivered to my front driveway. I need it to fill 2 new rectangle and 2 round beds in my backyard. Access to the back is via a standard size gate, which could be removed to allow a bit wider açcess.

Our storm water drain does not drain away water. When it rains or when hoses the water just pours out of the pipe. Close to some big roots and the side of the house. Older house so maybe old clay pipes? Just want it inspected with a camera or chuck an eel down to try clear it, I will rely on your advice

1. Remove old palings and wooden braces of old side gate. 2. Replace with new palings and wooden braces (already purchases and stained) 3. Remove current latch. 4. Replace with new latch. Steel framework to remain W: 2620 H:1820 You are to supply nails, screws and appropriate equipment

My back yard gate is hardto open. The hinge not working and the gate is bit hanging. Need to fix it. Thank you in advance

A wooden gate needs to be adjusted with appropriate tools for large bolts

Install an oscillot 2m cat roller on a side gate

The gate scrapes on the concrete driveway when fully open. The driveway slopes a little and is being raised by roots from a neighbors tree. The concrete has been previously ground but a longer term solution is to raise the gate on its hinges. I cannot stop the concrete being lifted by a tree root. As far as I can tell the posts are in good condition and the hinges and gate are also solid. I should say that there are 2 parts to the gate. So 4 hinges in total.

My colourbond gate needs repair/ replacement. It has cracked along welds, dropped and warped. I think that maybe a pedestrian gate might stop this happening again.

A tree root has raised the level of a garden path, so we need to raise the height of the garden gate, and take a few centimeters off the carport gate, so they both open smoothly. I’m just not confident using an angle grinder, drilling stew holes in steel and fitting the right sized screws.

Replace a broken gate lock with a new D&D (or equivalent) gate lock with key. Price includes you providing the gate lock.

I need vertical fence like pool fence with a gate . Total length is 3 meter including the gate. Please quote for the supply and install. Thanks.

The fence gates (1 narrow gate and 1 wider gate) were removed in the past. I would like to install them again. Not sure if all the extra items like bolts/nuts are still present.

Need to install a retractable baby safety door in the stair safely without any damage. Task is essentially making some drills (8 points), locating stud rightly. Product are something like this: (https://www.bunnings.com.au/perma-child-safety-1-4m-white-wide-retractable-gate-white_p0466947?store=7373&gclsrc=aw.ds&gad_source=1&gad_campaignid=21122993677&gbraid=0AAAAADtbEB8-5AjO42uA_Np5f8uadIX64&gclid=Cj0KCQiA0KrJBhCOARIsAGIy9wAKVUyuQNF7j6glS-bJLxUO_YYO4hwMGP7Q4SUoOxaAmQt9MAIBxEQaAkZEEALw_wcB)