Find a professional garage door installer in NSW

One of the garage door cables has snapped (the cable that runs over the pulley and connects to the torsion spring shaft). As a result, one side of the garage door is hanging lower and the door is no longer operating properly. I need someone experienced with garage door repairs to inspect it, replace the broken cable (or any other parts if required), re-tension the door, and get it working safely again. Please provide your total cost estimate, including parts if possible. Thanks!

Fix the garage door location

On/ off button is snapped off the chip board of the remote key. Needs aluminium solding and testing to make sure it is working properly

Garage door needs to be sand and paint ! It is timber

One of the garage door "brackets" requires 2 pot rivets + rubber strip needs re-fixing at one end See photos

Budget is call out fee only. Current motor: ATA GDO-9 Enduro Power point is working, but the motor has no lights and stopped working. Please include: * Remove the old motor * Disconnect/remove the existing white control cable to the wall switch (if needed) * Supply and install new motor * Setup and test remotes

Looking for an experienced garage door technician to repair my automatic garage door. Issue: ● The automatic opener has stopped working over the last 2 days. ● The door opens and closes easily when operated manually, so it doesn’t appear to be jammed. ● The motor/remote isn’t opening the door automatically. Looking for someone with experience repairing garage doors and automatic openers who can troubleshoot the issue and, if possible, fix it on the spot. Please bring any common replacement parts if appropriate (I’ll cover the cost of parts if needed). Located in Rouse Hill NSW. Flexible with times.

We have a garage door that manually opens with a garage door handle connected by two wires to unlock and open. The handle is lose and no longer works. You may be able to use the exisiting wires and just replace the handle.

We require supply and installation of garage doors . 2 car and single car tilt up panel. 5720mm wide 2650mm wide 2450 mm height Garage doors Please give me a quote to supply and install with or without motor

Im looking for someone to paint my garage door. It will need some sanding and prepping as there is some old paint peeling off etc. I have the paint ready to go!

I have a GDO-8 door opener. I need to reset the top and bottom limits. Also to program x3 remotes (which I have)

Re-align down pipe into drain

Please send through offers. Job obviously not for $10 😝 Need someone experienced with sectional/panel lift garage doors to repair an Ultralift garage door. One of the lift cables has detached completely from the drum/bracket area. The cable does not appear snapped, but the door is currently not being operated for safety reasons and will likely need the cable reattached, door re-tensioned/aligned and checked over. Door is currently closed. Please only quote if experienced with garage door repairs and torsion spring systems. Located in Revesby NSW. From my understanding this should hopefully be a fairly standard repair if no additional parts are damaged

Need help with fixing one bent garage door and supply and install 2 single garage panelled door opener in Glenwood area.

We need our sectional roller door to be repaired . It won’t roll all the way down. It gets stuck with a metre to go. Our original installer has closed his business down. We would also like at the same time do general servicing of it.

My garage door isn’t closing properly and seems to stop before fully shutting. The bottom rubber weather seal is damaged/worn and likely needs replacing. I’ve attached photos showing the current condition of the door and seal. What I need: - Inspect why the garage door isn’t closing properly - Replace the bottom weather/rubber seal - Ensure the door closes smoothly and fully Flexible timing, ideally ASAP

Looking for someone to wire a small smart home device (ratgdo32) to my Merlin MS65MYQ garage door opener in Miranda. The device is already purchased and the firmware is already installed — I just need someone to physically wire it up and mount it to the opener. The opener is ceiling mounted so you will need to bring a ladder. What's involved: • Connect 3 wires (red, white, black) from the ratgdo32 to the opener's terminal block • Mount the ratgdo32 to the opener rail using the included clip holster • Plug the ratgdo32 into USB power (powerpoint is right next to the opener) The job is straightforward — only 3 wires, no pass-through connectors, no wall button wiring. Full written instructions and photos of the actual terminal block will be provided. The orange pass-through connectors on the ratgdo32 are not used. Note: this is an Australian model opener so the wiring differs slightly from the standard US diagram. Instructions make this clear. Full wiring reference: https://ratcloud.llc/pages/wiring

Garage door to be taken down. Easy access. quick job just cannot do it on my own.

Then area under the garage doors need to be levelled with self leveling concrete (only a small layer) to make it look clean. There might be some minor grinding required in case clearance from bottom is required. Also gaps around garage doors will need to be sealed properly using rubber strip and between door and floor.

Timber above garage door has been replaced and needs painting. 3 different colours - all paint will be supplied. Please see before and after pics