Find an experienced fireplace installation professional in Mornington Peninsula

I want to install a fire/stove in my living area. Just want to scope the feasibility to do so and if or not it’s possible to do etc

Professional plumber to instal wood heater including standard hearth and flue requirements

Hello, have a scania edge 50 fireplace I need moved into position. Also Need help sourcing a compressed fibre cement sheet to place under fireplace (approx 20mm in depth cut to slightly smaller than fireplace base which is 482w x 334d.This will then need to placed on hebel bench and Fireplace needs to be placed on top ready for Plummer to install - if you are a qualified Plummer that can also install even better :) Fireplace is boxed on studio and needs to be brought into house so will need a trolley or two people perhaps as 100kg (I can try and help )

Removed a wood fire place in a shed and want to reinstall at a new location in the shed post renovation. Will need advice on fire proofing under and behind fire place

Need the coonara sanded thoroughly and painted with special heat resistant paint (a spray paint).

Hi I'm looking for a quote on a floating hearth, 5.8m long ( the approximate measurements of the unit are L: 5800mm x H: ~550/ 550 mm x W: ~550mm.) Ideally, we would like it installed in the next few weeks, to support a gas fireplace ( Heat and gf,o i35X) details : https://www.jetmaster.com.au/range/enclosed-gas/heat-glo-i35-x-freestanding/ Ideally, we would like drawers underneath in wood and a potentially stone / ceramic top similar to my attached image -

Need fireplace rendered Looking for a local Please don’t quote . I will only get the job done for $100 as to why looking for a local.

Bought second hand fireplace in good nick. Got the flue for it but will probably need more as our house is double story

I can’t seem to get the baffle plate out of my fireplace in order to clean the chimney. I think it must have warped slightly over time. I think the only way to get it out will be to use an angle grinder to cut it in half.

Just need a very heavy timber framed mirror to be safely attached and hung on the wall over fireplace please

Floor to ceiling wall with return to be clad/tiled. Product will be supplied. Measurements pending. Reply with interest.

We require an experienced handyman who knows how to find studs in the wall and hang our large, heavy, wooden framed mirror please. Mirror size is 1400 x 1200. We have a strong person here who can assist in the process too.

Need a tv mounted to the wall, believe it’s 65” Wanting the cables to run behind the wall so it’s nice and neat There’s a TV and sound bar We already have the tv mount etc which has been used previously at another house

I am looking for someone who can tile my fireplace. The vertical sections will require stackstone to be fitted to existing cement sheet. The horizontal section will require grey tiles to be fitted. All tiles supplied

I have an outdoor fireplace with a spinning cowlfor airflow up the top. It is making an awful sound and needs some lubricant inside it to make it stop. This job requires a ladder

Annual service of a Heat and Glow SLR-X Gas Fireplace.

Flute installation for gas fireplace

heat & glo fireplace can’t ignite, request for check and repair. I have confirmed the power point is on for the fireplace. We turned it off prior to leaving to go to the supermarket and when we came back and pressed the switch to the left of the fireplace to turn it on, it failed to turn on. I thought the pilot light might ve gone out so I looked up some YouTube videos, opened the bottom panel to put it back into pilot light mode and clicked the ignitor but couldn't see the pilot light come on anywhere.

I have confirmed the power point is on for the fireplace. We turned it off prior to leaving to go to the supermarket and when we came back and pressed the switch to the left of the fireplace to turn it on, it failed to turn on. I thought the pilot light might ve gone out so I looked up some YouTube videos, opened the bottom panel to put it back into pilot light mode and clicked the ignitor but couldn't see the pilot light come on anywhere.