Find a local electronics repairer in North East Melbourne

I have a GHD hair straightener that went into a safety shutdown as my son was playing with the power switch, turning it on and off while I was using that hair straightener. It is not turning back on. It shows a red light around the power button and beeps and shutdowns every time I try to turn it on.

CONCRETE STEPS AND PLANTER BOX.​​​​​ Excavation of stair and planter box area to 200mm below existing ground. Excavation of 300mm diameter x 3000mm deep bored piers x 13 of, to support concrete. Excavated spoil to remain on site. Supply and place concrete to bored piers. Supply and place steel reinforcement and concrete for base of stair and planter construction. Supply and place formwork, steel reinforcement and concrete for planter box, including plumbing for drainage. (2000mm wide x 1000 depth x 1300mm high.) Internal tanking of planter box by others. Supply and place formwork, steel reinforcement and concrete for stairs as per design drawing.

Digging loose and moving some top soil by wheel barrow. 2 hour job

I need a connecter soldered on but board might be damaged and might need the whole board transferred to a new board . But I have no idea where to get the same board that’s ready to have everything soldered on.

The front steps are concrete and painted but need sanding back, properly prepared with concrete/masonry primer and painted with proper concrete/masonry paint x 2 coats or more if required.

Hey, I'm looking for someone experienced to repair my Asus Rog Delta gaming headphones. The problem is at the jack connection where it plugs into the headphones – the audio cuts in and out unless I wiggle or pull on it, which is extremely frustrating (especially when I play Valorant). I’ve tried to get it RMA’d but Asus requires the original receipt, which I no longer have. I’ve been told by a previous repairer that the wires inside might not be straightforward because it’s a gaming headset, so please only offer if you know your stuff and have done similar jobs before. If you can also replace the jack or socket at the headphones, great – the main thing is getting a durable and tough resoldered connection, not just a temporary fix. Microphone is built into the headphones, so ideally the mic will work after repair too. The area looks fine with only slight fraying, nothing too major. Happy to provide pics if you want. Being cheap on price is important, but I value skill and creativity to get the job done right. Bonus if you’re near 3095 Eltham, Victoria, but I’m happy to come to you anywhere in Melbourne or organise low-cost shipping and return post (e.g. $10 postage using return-to-sender to keep costs down). If this sounds like your kind of job, please let me know your experience and your quote. Thanks!

A few paint chips on a wall, and a windowsill need patching before I vacate my rental

Form working of concrete floating steps

Need to change hdmi port for ps5

Change the tap in the kitchen to a retractable dual spray mixer. Change 2 bathroom taps and mixers. (3 sets) Change the bath sets. All have been purchased.

Fix 2 taps which are shaky 1. Washbasin tap (this might need moving the basin and do it or even put a new one (I will have a new tap stand by)- see pics ) 2. Sink tap - this might be an easy one - It just keep shaking even after I fix it with my hand. So just need a good fix so that it doesn’t keep shaking

Needs to paint a patch on a wall that has been painted but with a wrong white paint. Need to paint that and few touch ups trough out the apartment for a rental property.

There was a hedge that has been removed, but the stumps are still in place and need to be ground down. There are seven small stumps in total. Stumps with small limbs will be cut back so only the stump remains for removal. When: Needs to be completed before Monday.

Trim Laminate benchtops, one sink cutout and join prep for two straight corners (routing recesses) required. Trimming - There are 3 benchtops 1. Trim 246 cm benchtop to 240 cm and cut sink opening. 2. Trim another 246 cm benchtop into two sections (~75 cm and ~130 cm). 3. Trim a few cms either side of 240 cm benchtop (cut a few cm off each end to remove damage sustained in transit). Cut one sink opening Prep straight corners - router underside recesses for connector bolts. Please quote price - also happy for you to quote second quote for install onto cabinets - existing cabinets - all level.

My gas hot water system Dux Prodigy ignition/pilot light keeps turning off and won’t stay lit. I managed to follow instructions and the flame stayed on for 2hrs and now the flame won't light up when following the instructions.

We want two new taps installed outdoors. One at ground level near existing pipes and one almost directly above this on the upstairs deck. Pics of existing supply and approximate placement of taps desired. We can provide the actual taps only, but not the pipe or anything else that might be needed.

Replace two taps in the kitchen with two pull-out taps. Images attached for reference. Must be licensed plumber.

Need an experienced handyman or plumber to fix leak/drip in 4 spindle taps: • 2 basin taps (hot & cold) • 2 shower taps (hot & cold) • All taps are the spindle type and currently leaking. Requirements: • Supply suitable washers ( for spindle taps) • Bring your own tools • Ensure taps are reassembled correctly and not leaking

Need a paint and plaster work touch ups for a property in Donnybrook. Photos attached for your reference.

These two taps are the most used taps in the house and leak especially during the winters. They used to drip and now have started to flow in a tiny stream even when the tap is closed and shut very tight. The house was built in around 2005. We will prefer to work with someone with registered plumbing experience.