Find trusted local electricians in West Brisbane

Looking for a licensed electrician to connect power to a new sliding gate motor at a residential property in Riverhills. Scope of Works • Electrical installation, cable run and final connection only. Exclusions: • Sliding gate motor has already been purchased. (Brand: LEXOautomation). All gate automation equipment has already been supplied.No equipment procurement required. Cable Route: The switchboard is located on the left-hand side of the house and the driveway. The gate motor is located at the front fence near the driveway entrance, adjacent to the letterbox. Right-handed side of the driveway. Approximate route: • 2m from switchboard area • 6m along side access • 7m to gate motor location Approximate cable route is 15 - 16m. Maybe allow approximately 20m total cable length including wall rise, terminations and installation allowance. The cable will need to cross sections of existing concrete driveway. The concrete side path is about 1 meter wide. We plan to wire the cable underneath across the side path. The wall rise from ground level to the switchboard is approximately 1.6m. A site sketch showing the proposed route is available and can be provided together with photos. Please kindly provide separate pricing for: Option 1 – Homeowner excavates trench under electrician's direction; electrician supplies and installs electrical works only. Option 2 – Electrician supplies all labour including trenching and electrical works. Please also advise (if you could): • Required trench depth. • Your preferred method for crossing the concrete driveway. (Our preferred route is drawn in the photos) • Whether a dedicated circuit is required. • Any additional materials required beyond the supplied gate equipment. • Whether a Certificate of Compliance can be provided upon completion. Power is available at the existing switchboard and access to the proposed cable route is clear. Please send your quote and availability. Location: Riverhills QLD 4074

Hi, I need a licensed electrician to: Disconnect and remove my existing hardwired electric cooktop. Install a new power point inside the cupboard underneath for a gas cooktop ignition. When quoting, please confirm your availability and include your licence number. Thanks!

I am seeking a licensed electrician to install two new double power points in my home: 1. Location 1: Adjacent to an existing NBN/data cabinet and existing power outlet (see photo). 2. Location 2: Upstairs study/home office area to provide additional power for computer equipment and printer (see photo). Requirements: * Supply and install two new double GPOs. * All work to be completed by a licensed electrician.

Need an electrician to install a chandelier

Looking for a Qualified Electrician , Ongoing Motel Work We are currently looking for a reliable and professional licensed electrician for ongoing work at a motel. The work may include maintenance, repairs, installations, lighting, power points, and general electrical work as required. We are looking for someone who: • Is licensed and experienced • Can provide quality and professional work • Is reliable and responsive • Can offer reasonable and competitive pricing There is potential for ongoing regular work for the right person/company. If you can provide a good price and quality service, we would be happy to work long term. Please contact us with your details, experience, and best pricing. Location: Indooroopilly

1) Electrician required to wire in a new electric oven and induction cooktop. About 10m from switchboard. Would like a replacement isolation switch and breaker etc. Old freestanding unit is 2m away but existing cable likely undersized. 2) Also replace 20a breaker in board that has the brown stain on it -was from battery acid leaking. House is a post war on stumps (1-1.8m high).

- Swap electric cook tops (unplug old, plug in new) - unplug an old oven/cook top - change bulbs in garage lights

I'm replacing a gas hob with an induction cooktop. Looking for an electrician to run an 33A, 7400W line to where the cooktop will be installed (2nd floor). Cooktop already has a line but only for the igniter and rangehood above. Existing gas line will be capped off before that by gas fitter.

Require qualified electrician with solar ticket to replace 3x hail damaged solar panels. I already have the replacement panels. Just require installation and disposal of old panels

Install cooktop 60cm and oven 60cm and rangehood. All going into existing cut outs with previous electrical input (appliances removed less than month ago) . Cooktop will need own isolation switch.

Licensed Electrician Needed – Riverhills QLD We have a vacant 2‑storey townhouse in Riverhills and require a licensed electrician to: - Remove 14 existing direct‑wired fittings - Supply and install 14 plug bases into the existing 90mm ceiling holes Timing: Work must be completed before Monday 4th May. Only reliable, careful trades please. If you’re available and able to assist, please reach out. Thanks, Rachel & Tim

Just need new GPO installed, existing one not working due to age. Have the new one here so literally just the labour.

seeking an electrician to fix a new plug point on a electricity cable. previous LED fixture not working and needs to be replaced with a new one. One the cable is fixed deep in the roof, a new socket is required to fix the new LED light.

Seeking to replace a ceiling light. Previously installed ceiling fan with light. Image of LED lighting provided.

Fix air con please- unsure why it isn’t working.

Install 3-phase reference wiring + Shelly energy monitors in switchboard (licensed electrician) Scope: - Install 1 × 3-pole DIN MCB (metering/reference circuit) - Install 5 × Shelly 3EM-63W Gen3 units inside switchboard - Provide clean L1 / L2 / L3 voltage reference distribution to all Shellys - Connect: - Neutral to neutral bar - Earth to earth bar - Install and route CT clamps (3 per device = 15 total) on nominated circuits - Neatly terminate, label, and secure all wiring - Test and verify correct operation (phase alignment and readings) Requirements: - 3-phase switchboard (Hager gear) - Must be fully compliant (AS/NZS 3000) - No double-lugging of breaker terminals - Preference for clean, scalable solution (e.g. terminal blocks or equivalent) Notes: - All Shelly devices supplied - Switchboard has available DIN space - Looking for a neat, professional install — not a quick patch job Please include: - Confirmation of licence - Approach you’d take (brief) - Availability Location: Kenmore

Need licensed electrician to disconnect and remove cooktop and oven and rangehood

Our sky light was damaged by hale and need to replace

I need to fix One power point in living room and next living room patio sealing light not work as well after renovation. We disconnected 2 power point at living room.

[Quick Easy Money over Christmas Holiday] These are the jobs we need assistance with. 1. Disconnecting the main power supply to an electric stove and installing a new stove with a power switch. 2. ⁠Replacing the range hood. 3. ⁠Installing 5- 6 Ceiling fans