Find a local console repairer in West Brisbane

Laundry is next to the kitchen and need to relocate this to the garage, the move of the water taps is from one wall to the opposite side (approx 1m) and need to reroute the drain to work with the washer in garage.

need to remove 2 tree stumps just below ground level. access is available. dirt can remain onsite.

Looking for someone to remove tiles and taps, and plaster

Hi, I’m looking for someone to grind/remove two tree stumps at the front of the property. There are two stumps: * One larger stump * One smaller stump The frontage/access width is at least 3 metres, so a stump grinder or similar machine should be able to get in. Please bring your own equipment and all the dirts and mulch could stay on site. Please provide your quote and availability.

Remove approximately 8 stumps off retaining wall

Plumber required to replace taps and spout of bath and create a connection for a washing machine. Note Bath maybe add later but now just need washing machine connection. I will supply new taps. Need it done asap so tiling can commence.

Replace the these timber steps with new merbau pre-oiled decking boards similar to below. https://www.bunnings.com.au/140-x-19mm-5-7m-merbau-specrite-joined-set-length-pre-oiled-decking_p0177414 1. Please provide quote to Supply and install at Mitchelton QLD, 2. Option for new screws vs using existing. This job is not urgent.

Fisher & Paykel DishDrawer model DD60DCX9 (Product 81587-B). Both top and bottom drawers stop mid-cycle and display A6 with the Rinse indicator. The issue occurs on both drawers. Power cycling at the wall restores operation temporarily and the drawer resumes from where it left off, but the error returns repeatedly until the cycle eventually completes. Already checked for obstructions and cleaned seals. Looking for diagnosis and repair (possible lid actuator / control issue).

Have a few stumps left over from tree removal that need grinding down to remove roots etc. There is a palm tree stump that was not finished rather just covered in bark but needs the ball of roots removed and able to be ready to start prepping a concrete area including for a plumber to dig a trench on Monday.

I have a toilet that squeaks after I flush I also want to change three taps (two bathroom sink and one kitchen sink) Need this done next week if possible. Can be flexible with dates and times

Just need old sink spout/taps changed over to new ones. Have all the parts. Need done asap.

Brick patio (front, back) and driveway and brick pavement around the house needs sealing with jointing sand/ paver sand, sweeping, spraying to set. Material costs and labour to be covered in the quote . Patio has been recently pressure washed. Very few weed, need to be cleared before the job.

Toilet leaks when flushing, and he water seeps through under and through the wall .

toilet cistern is broken, kitchen mixer tap turns around when turning tap on or off, wanting to replace standard garden taps with 1/4-turn taps

I need someone to remove and dispose 2 x golden cane palm stumps. Stumps have been poisoned about 3 months ago, and again about 1 month ago.

I want to have some painting touch-ups before the end of my lease. It is a 2 bedrooms unit, and the work would mainly involve minor repainting.

Upstairs timber floorboards in our living room are loose and squeaky, causing loud banging and creaking noise in the bedroom below. Looking for a carpenter to secure the boards properly by screwing into the joists (not just nailing). This is a small, targeted repair in high-traffic areas (around couch and walkway), not the whole floor. Access is easy and we can show the exact noisy spots. Looking for a proper, longer-term fix rather than a temporary solution. Price negotiable!

Water tap in Kitchen has low pressure but other tap are fine. I guess it needs cleaning or may be replacement

I have two dripping taps that need to be fixed. One outdoor, the other in a bathroom sink.

I need 4 golden palm stumps ground out to the level of the existing artificial turf, approximately 300 mm deep. Grindings can remain on site.