Find an experienced builder in West Brisbane

Looking for someone to install the new garden shed. 2.3 x 3x 2 m.

3m * 3m shed assemble, I have already done one side.

We have a very low rise brick fence that is fractured in parts and needs demolition along with a slightly higher small fence section on the other side of the driveway. Looking to have it removed and disposed of.

I have a patio ceiling that I want to cover with white James Hardie 2400 x 750 x 4.5mm 1.80m² HardieFlex™ Eaves - 2400 x 750 x 4.5mm Can be supplied from Bunnings. Measure Supply material Install Clean & Tidy work area.

- provide, cut and install new laserlite roof sheeting - install one new batten to match 45x70 existing - seal and flash at edges, tie into existing gutter - optional extra to fix 1 gutter clip and base of existing column - existing sheeting has been taken off - existing flashing can be reused if desired - approx 7400 wide, existing sheets 1740long - have kept existing roof screws, may still need a few new ones though

1)Remove 2 x stirp pegs concreted in the ground, remove 2 x poles used for cloths line also concreted into the ground. 2)Set up Flat pack pergola from bunnings, drill into concrete to bolt legs down. 3.5m x 4.2m Happy to negotiate as there are other things that need to be done.

I need someone to fully dismantle and remove an old pergola structure from my backyard (see photo). This includes: Carefully cutting and removing the two rear beams that are attached to the fence posts. The fence must not be damaged or removed. Digging out and removing the two front pergola posts. Digging out and removing two additional timber posts nearby (as shown in the image). I can provide 2 waste vouchers.

Section one 3m by 3m by 3m pergola . Section two 3m by 3 m pergola. Timbers and bolts for base plated supplied. 4 holes by M16 bolts are needed to connect base plate to post. Will need about 50 in total. 24 holes by 7mm fasteners are needed to connect top plate to post. Will need about 1000 in total. Will need own tools. Professional done. Looking for quality results.

Move the dust and sand 3m to the carport

We need a timber 1.8m high fence (overlapping and capped) to go beside a driveway. No need to remove an existing fence. Easy access. About 31m.

Area cleared and concrete slab measuring 3m x 3m put down. Erect EasyShed

All of the walls are built it just needs to be assembled

We need a Shed 3m x 0.78m Narrow Slider Shed from Easy Shed to be assembled.

Need a roof built from house to fence to enclose small area

One side of my garage is open. I want to enclose this side with a framed up cladded wall for at least the top third. Bottom two thirds could be vertical battens. Needs to include a door. Dimensions of the space to be enclosed are 6.7m x 4.04m. Posts would need to anchor to existing concrete slab.

Looking for someone to supply paint varnish on a Pergola in Sinnamon Park

We need our stracto umbra pool bar / shed installed. Concrete slab is installed and tiled. Would need to bolt into that. https://www.stratco.com.au/au/sheds--garages/garden-sheds/umbra-awning-shed/?srsltid=AfmBOop80OI7RBcKrU9I3aUh1cUnOHdD4CN-9TtFP4zD8CVo6_UwN5eT

The piece where the driveway meets the road has split. Need a new concrete piece (like a long wide sleeper)

A small Spanbilt flat pack shed to be picked up from Crestmead and delivered to The Gap. Would then need a little help to install

Branch requires support with hessian strapping to pergola. Literally a 20 min job. I have ladder and strapping.