Find local air source heat pump installation & repair in VIC

I want to replace my existing gas hot water system with an energy-efficient heat pump system. Looking for a licensed and experienced installer who is approved under the Victorian Energy Upgrades (VEU) program and can help apply the rebate.

Had a new heat pump hot water unit installed (Aquatech X6) and not happy with the current positioning. The job is to move the unit and concrete base 45cm (which maintains the 60cm clearance required) and adjust/extend the pipework as needed, including relocating the unit’s two drainage pipes around the corner so not as prominent from house. The unit must remain level (maximum 3° tilt) and maintain manufacturer clearances as per the Aquatech installation requirements (actual physical manual will be provided if needed). No electrical work is required. Must be a licensed plumber. Please provide all costs upfront. Payment via Airtasker only. Photos attached for reference.

We have 2 heat pump dryers, one (stirling brand) is working but making a funny noise and the other (fisher & paykel) stopped working. When you turn it on it spins a couple of times then stops spinning but the motor is still running

I am only eligible for VEU and STC rebate NOT ELIGIBLE FOR SOLAR VICTORIA REBATE The existing hot water system need to be disconnected: Rheem Stellar 330L Gas Hot Water Heater

Install a new heat pump drier by piping the condensation hose into the laundry trough and help lifting the drier up onto the washing machine already installed underneath. I already have the stacker device ready.

Dryer has a screeching sound when operating

Hi I have a heat pump dryer installed above my washing machine in the laundry. Currently I need to manually empty the water tray. I would like it to empty automatically. There is a way to do that, so the water from clothes automatically drains. I have a hose for that but please bring any attachments that may be needed. Thanks!

My heat pump water heater has just shut itself up. When someone checked it, the issue is burnt neutral and earth bar for isolator. The recommendation rectification is to supply and install new NHP 35A tall weatherproof isolator. Can you please quote me for this work. Thanks

Our dryer has screws and rivets go through it, now there seems to be something stuck behind the drum. We will need the drum taken out and to removed the screws/rivets.

Teka dryer stopped spinning

Hi , We are looking to replace our old Sunpro Dux hot water heater system with newer version - like to like . The current system has solar panel which is still working efficiently -,we would want to retain this . Despite the gas pump being malfunctioning/ not working we have been getting hot water for past month it two ( being sunny days ) We would like to replace the gas heat pump but keep the solar connection - if possible .

Concrete slab for new electrical heat pump to sit on. 700 x 700, it’s on a slope and concrete underneath slightly cracked.

I'm looking to replace my current gas water heater with an electric heat pump. That will also mean needing some electrical work done. And finally, I'll need to have my old water heater removed.

Haier 8kg Heat pump dryer is getting very hot after drying a load- filter and condenser filter cleaned often and still have issue. Is there any way to resolve this?

Heat pump dryer not collecting water or drying clothes - turns on and runs the whole cycle

My Emerald Energy heat pump hot water system is playing up. Two issues: 1. The pipe running to the gutter (TPR discharge pipe) is releasing a large amount of water constantly 2. We’re only getting lukewarm water — not hot

I’m having an issue with my Bosch heat pump dryer—it’s not working. The store advised that the motherboard needs to be replaced as it was damaged by pests. If anyone can help with repairs, please contact me. Thanks.

need the pool heat pump connected. What’s already in place: • 32A breaker in the switchboard dedicated to the heat pump • 6mm cable already run from the breaker to the isolation switch • Isolation switch installed next to the pool equipment • Heat pump is in position Scope of work: • Open the isolation switch and confirm the 6mm feed is correctly terminated • Run the final connection from the isolation switch into the heat pump • Test the circuit to make sure it’s drawing correctly on the 32A breaker

Bosch Serie 4 dryer WTH85200AU - runs but very inefficiently. Clothes take forever to dry on all settings. Need someone to see what is wrong with it.

my dryer keeps showing an error message saying “the water tank is full, please empty and continue the cycle.” But the hose is connected straight to the sink drain, so it should be draining automatically. It seems like either water might be coming back up the hose, making the dryer think the tank is full, or the hose itself might be blocked. If someone could check it out, I’d really appreciate it. No rush..