Find a local electronics repairer in West Melbourne

There are several unsealed gaps throughout the property that could allow entry points for pest. This include gap under the main garage door, a gap around the laundry door and a hole beneath the kitchen sink.

Hi, I need a careful paint touch-up repair for a small stone chip on the front bonnet/hood of my Tesla Model Y. The chip is about 1.5–2mm. Paint code is PPSW, Tesla Pearl White Multi-Coat. There are a few very light surface marks around the chip, so I’d like light polishing around the area if possible. I’m not looking for a full panel repaint. Touch-up only. Please avoid sanding or heavy machine polishing unless discussed with me first. Please let me know your process and whether you have the correct PPSW touch-up paint.

*The shower sliding screen door is faulty, it doesn't slide. * Blind cord anchors are required to be installed throughout the property including in bedroom 1 and dining room. *Bathroom- noted 2 cracked shower wall tiles *Shower base seal requires replacement *Bathroom cornices have gaps

Have moved a queen bed frame, headboard wont fit upstairs at new place, dont know how to safely break it down. Help break the headboard down, so it can fit upatairs, take upstairs, then re-assemble the full queen bed frame.

IKEA KLEPPSTAD Wardrobe Assembly Looking for someone to assemble an IKEA KLEPPSTAD wardrobe. • Location: Hoppers Crossing VIC • Date: Wednesday, 8 July 2026 • Time: 2:00 PM • Budget: $50 The wardrobe will already be unboxed and all parts laid out prior to arrival. Assembly only required – no unpacking, rubbish removal or moving of furniture needed. Please quote your experience and availability when making an offer.

I have concrete floor outdoor at my porch areas where I am planning to lay tiles, refer to pics. Also, looking to put tiles on the concrete retaining walls next to it.

I need a triple bunk bed to be taken upstairs and put together. Need it done today as it’s currently sitting in my lounge room and becoming unsafe.

1. Basin p-trap appears to be old. Smaller than 40mm and screwed on so tight i can't unscrew it! There is an old thread that is stuck inside the opening of the P-trap. So that P-trap needs to be either partially or fully replaced in order to connect the 40mm down pipe from the basin. 2. Bathtub drain pipe split when trying to fix the basin P-trap. Appears to have had a dodgy patch job that has not held up! Likely just needs a small part of the pipe replaced. This is all under the house. Direct access from under the house is available, and also accessible via a hole in the bathroom floor where the basin down pipe is. Please send through quotes and availability. Questions welcome :) Thank you!

Looking to fill the gaps between the slab and shed sheets at the bottom per photo. Probably mortar or calking Size of shed is roughly 15x10m Location taylors hill

Need my power point inserted back to the wall and some wall scuffs repaired

I have about one hour of odd jobs - assembling a cat run, lifting a light cupboard up 1 flight of stairs (with me) and if there is time, a few odd jobs.

I have a couple of tree stumps that need removing on my front lawn.

Shower taps needs to be fixed/replaced. hard to turn off

Scope of Works: * Fill visible gaps between melamine panels. * Fill gaps in skirting boards. * Caulk/seal all visible gaps to provide a neat finished appearance. * Sand and prepare repaired areas ready for painting.

Fill in the gaps between the gaps of the bricks

We require the shower head and shower taps (see photo) capped off/removed over bathtub (keeping bath taps and spout as functional).

Fix 3 x Leaky Twin-Handle Mixer Taps (Bathroom) Hi there, I need a qualified plumber or experienced handyman to change the rubber washer for three leaky taps in my main bathroom. All three are traditional twin-handle mixer taps (separate hot and cold handles, but a single shared spout/outlet). The 3 locations are: 1 Bathroom wash basin tap 1 Bathtub tap 1 Shower tap

Need done on Monday 18/5 (Today) Lower my laundry taps to be under benchtop, you’ll need to supply a new noggin and new taps that are slim to the wall to fit my washing machine/dryer in front of them. Please also supply the right fittings/crimps to the pipework no push fittings. Happy for Plukber to make a hole I’ll get it patched up later.

Replace the current tap with a new tap