Find a local console repairer in South East Perth

Looking for an experienced handyman to set up low-voltage cable routing & conduits for under-step LED lighting in TWO areas: Porch and Alfresco. ​Scope of Work (BOTH Locations): ​Cable Routing: Run 2-core low-voltage cable down double-brick cavity walls. ​Top Cable Labeling: Securely tag/label the top cable end with bright electrical tape inside the wall for the electrician. ​Wall Exit: Drill a neat hole through the bottom mortar joint and pull the cable through. ​90° Elbow: Install & seal a 20mm 90° PVC elbow into the wall exit using masonry adhesive/silicone. ​Conduit Laying: Connect a 20mm Medium Duty rigid PVC conduit (using PVC cement) to the elbow and lay it toward the nosing rebate location. ​Slurry Protection: Tightly seal/plug conduit ends with heavy-duty tape to prevent wet concrete ingress. ​Supply: Handyman to supply all materials (cable, 20mm conduit, elbows, glue, adhesive, tape). ​Requirements: ​Clean work with zero brick damage. ​Send clear photos/videos of finished conduit runs & labeled cable ends before concrete pour. ​Please quote all-inclusive for BOTH areas (labor + materials). Thanks!

I’m looking to replace my existing outdoor decking with eco decking and build new steps leading from the deck. The work includes: • Remove and dispose of the existing decking • Inspect and prepare the supporting structure • install the new eco decking (I can purchase materials) • Build and install new steps • Complete any required framing, supports, fixings and trims I will supply the decking and other materials. An inspection can be arranged before the quote is finalised.

Need two new taps on bathroom basin. The cold water tap keeps spinning around and no water comes out of it.

I need 3 benchtops for my unit kitchen and laundry. I have attached copies of the plans for my kitchen and laundry upgrades. Probably fitted in about another 2 weeks when I will need the benchtops fitted. At this stage I am looking for an estimated cost for providing the benchtops, cutting of holes for the kitchen sink and laundry vanity basin and tap holes for both and the fitting of all 3 benchtops. I haven't chosen the sinks or taps yet so I cannot confirm the exact location or sizes of any openings. I am looking for a freckled marble like finish with 20mm edging. Could you please quote the total cost and whether you can fit the benchtops in about 2 weeks' time.

ignitor keeps clicking and making spark even after the burner starts burning.so now i turned off my electrical switch

I have cut down 7 small trees and require the stumps to be removed from the ground I will dispose of

Removal of tree branches, cut down of 1 tree and removal of 2 stumps

Leaking taps and showers new toilets

Shower leaking but think its a tap problem.

Replace kitchen mixer. Replace washers on one sink. Service sweaking tap on one sink.

Hi My Gas Hot Water system keeps turning off, something probably it’s thermopile needs replacement (I’m not sure).

Remove the stumps of four previous hedge plants. See the size of the stumps relative to my foot in the pic.

Have switched the dishwasher off at the wall as it was making an engine sound without working. When water is put in the drain it drains properly so I don’t think it’s a draining issue. But when I turn it on at the wall it attempts resuming a cycle before resting on the 27 minute light.

I have a new set of taps for my bathroom basin, I would like the old taps replaced with these new ones please 🙏

In Both Toilets, water runs into toilet all the time. Note that i have same issue in both toilets. Also, I need 2 taps needs to tight up

Kitchen and shower taps leaking, please check if they can be resit or need replacement, its a rental property so I just need to get the jobs done

Need to fit two cold and two hot taps. One spindle available to test size (tried to do ourselves) with 4 new tap handles. Both wall mounted; one above utility sink and one above washing machine.

Lower 2 sets of taps under bench, connect new sink and connect new tap ware to sink for fully functioning laundry / Scully.

One of the safety switches in our switch box has jumped and I've unplugged everything in the house which I can find, it still wouldn't reset, I then switched off the main switch and reset that switch, it will stay up for a minute before it jumps back to off. I think I need someone to come take a look.