Find a local circuit board repairer near you

Controller for manager30. Cat5 socket has come loose and at least 3 tracks have come loose on circuit board. Needs coating to be sanded or scraped back and soldered back onto the loose tracks

I have installed blackvue 750-2ch camera in my car. At the moment the dashcam runs on the battery power. when the engine is turned off. as a result car battery is drained and I cant turn on y car. I want the settiing on the circuit board to be changed in a way the dashcam is turned off when the car is turned off.

DESCRIPTION: Small micro-soldering job on one 4-layer circuit board (heavy copper), Adelaide. Job 1: Replace 3 SMD resistors on the top side (R25, R27, R29). All are 0402 size, changing from 30 ohm to 2.7 ohm. Job 2: On the underside, lift one end of two 0402 resistors (R9 and R12) so each stands upright, then run a thin insulated wire from each raised end, round the board edge, to a pad on the top side. Glue the wires for strain relief. I can supply the new resistors if you don't have them and a job sheet with marked photos of every location. The part labels are printed on the board. You'll need: a stereo microscope, a hot-air rework station, a board preheater, fine-tip iron, flux, thin insulated wire (30 AWG). Please mention your micro-soldering experience (phone or laptop board repair is ideal), and include a photo of your bench or past board work. Please measure each new resistor with a multimeter afterwards.

Need the DC charging port re-soldered back onto circuit board.

Gas hot water circuit board

Power supply receiving plug has broken off circuit board I can bring it to you if you in my area

reconnected a connector the wrong way after repair on a golf buggy. May have fried circuit board. display does not turn on. likely fried surface mount fuse or zero ohm resistor, TVS /reverse polarity protection diode or the voltage regulator. Can you help. am able to drop off circuit board. Have taken handle apart and controller out.

I have a tenant in my rental property and they have mentioned that one of the ceiling lights went out and then the circuit board started making a noise. They haven’t described the noise, but they are worried about it causing damage.

PCB in Mitsubishi compressor unit has a communication error to one of three indoor heads. Parts no longer available. Evidence of overheating of the 24V control supply

It’s a Mukuta 10+ E scooter, was changing tube everything is normal, when put motor wire back, the rear left fender 4 wires came/stretched off the black compound of the circuit board, wires are not wrecked though. the lights for that fender don’t work anymore, Just need them back onto the black compound, maybe re wired/melted back on or so for them to work again

I have a ride on remote car for a child but the remote was damaged by leaking battery and does not work. One of the wires would also need to be resoldered. The stop button is also not working, it won’t depress.

It looks like there are a couple of lights or resistors missing from an accident. They need to be repaired

Rear ECU on Toyota Landcruiser is suspect.

Quote the circuit upgrade

Needing a circuit board replaced for a Proform 2000 Treadmill

Circuit board replacement

Already posted on here for replacing caps, resisters and general servicing of pcb boards

Storz & Bickel VEAZY - Dry Herb Vaporizer Looking for an experienced electronics hobbyist or bench technician with micro-soldering capabilities (fine-tip iron, flux, and ideally a microscope setup) to repair a high-end dry herb vaporizer. The Device & Materials:Model: Storz & Bickel VEAZY (a premium, German-engineered medical-grade device). Casing Material: The outer shell and internal structure are made of medical-grade PEEK plastic (Polyether ether ketone). This is a highly heat-resistant engineering polymer, but it is tightly sealed. It needs to be pried open gently with proper plastic opening tools without snapping the plastic tabs or melting the housing during solder work. The Issue:The device has an internal connection failure. I need a technician to open the PEEK casing, inspect the main logic board, and re-solder the broken joint. This is likely: Option A (If not charging): A fractured pin connection where the USB-C charging port meets the PCB board. Option B (If not turning on): A loose/snapped power wire connecting the single-button system or internal battery to the motherboard terminal pads. Important Note on Warranty:Please note that I am deliberately choosing to bypass the official manufacturer warranty process due to the long turnaround times for international shipping as well as not purchased in Australia. Because opening this device permanently voids my warranty coverage, I need someone meticulous who will treat the board with care, apply proper flux, and ensure there are no bridges or short circuits before re-assembling. Logistics:I can drop the device off to you if you are located around the Campsie / Inner West / Canterbury-Bankstown region, or you can here. Please offer your price based on a quick bench diagnostics and point-to-point micro-solder reflow.

I need navman cruise650mmt usb soldering back on circut board. Already removed.

The tactile button I use to switch my cycle camera on and off is no longer working. Luckily there's another tactile button on the cam that I don't use. Happy to drop off around Sydney metro area. Looking for someone with the skills to de-solder the buttons and swap them over so I can use it again.