Find a local electronics repairer in Inner South West Sydney

Left speaker wire loose and intermitttent sound

Chips and gauge laminate flooring repair

One of the timber steps on my internal staircase has collapsed and needs repairing. The carpet and underlay have lifted, exposing the timber underneath. Looking for an experienced carpenter to inspect the supports, repair or replace the damaged step, make it structurally safe and refit the carpet if possible. Photos attached. Located in Milperra, NSW. Please provide a quote including labour and materials.

My Bosch heat pump dryer series 8 keeps flashing the error code of the water not draining (as shown in image). I've cleaned the filters and nothing is blocking it from getting drained from my end. I'm assuming something internal needs to be fixed.

FEMALE ONLY. 6 drawer malm dresser from ikea. need the flat pack boxes moved to my room upstairs and need the drawer assembled

Looking for someone to remove/grind down approximately 12 old tree stumps and exposed roots around my property. Stumps vary in size. Photo attached as an example of one of the larger ones. Would like them removed or ground down below ground level so the areas can be tidied/covered with soil afterwards. I have a green waste bin available for smaller waste that can fit. Please include any other waste removal required in your offer. Please bring all required tools/equipment. Located in Carss Park (near Hurstville)

Replace cut cord on ghd Platinum+ straightener Looking for a qualified electrician or appliance repair technician to replace the power cord on a ghd Platinum+ hair straightener. It’s an unused display unit, and I’ve been told the cord was cut for display purposes. It’s cut close to the swivel base—photos attached. Please quote for a complete replacement cord/swivel assembly, including parts, labour and electrical safety testing. Experience repairing ghd straighteners preferred.

fix up little bits of pieces before selling home, painting, touchups

Looking for someone to help install a GPS screen and reverse camera in my 2003 Toyota Corolla Conquest. All parts and cables are supplied. I’d appreciate it if everything could be installed properly and tested to make sure it’s all working well. Thank you

I need someone to assemble my IKEA KLEPPSTAD wardrobe. It is a two door sliding door wardrobe and 3 drawer MALM chest of drawers. I will dispose of the rubbish so you don’t need to take it away. Needs to be done around 1:30/2pm today as the item should be delivered around 1 pm

I have a standard shower, after a while water starts to seep out from the shower area and on to the bathroom. I think sealing issue of door or borders?

Replace glass and doors,

Please help me build this pool table from a flat pack. Who is available to build it tomorrow afternoon?

I need the power point installed. Tile has been cut and the wall behind is gybrock.

We need installation of replacements for the following (all purchased already): - 1x Sink Taps + Spout - 1x Bath Taps + Spout - 1x Shower Taps + Showerhead Licensed plumbers only.

Supply and fit EZYFIX Chrome Classic Washing Machine Taps ($81.40 at Bunnings) to a house in Sans Souci If you have an alternate suggestion on the taps (for example if you have a brand new set in hand and recommend that instead) then please include details in offer. Happy to be flexible so long as the taps are good quality.

I need my two back door steps built. Ideally timber block boxed steps. It’s only two steps and timber will be provided. I am Open to some other way to build two steps if you have an idea

Job Title Wardrobe Dismantle & Plaster Patching (Upstairs) - DISPOSAL OPTIONAL Description Looking for a handy person or carpenter to completely dismantle a built-in wardrobe system from an upstairs bedroom and patch holes left in the drywall. Waste Disposal is OPTIONAL. Please provide a price breakdown in your offer: Base Price: Dismantle wardrobe, carry pieces downstairs, patch walls (leave materials stacked on-site). Add-on Price: Fully load and legally dispose of all materials offsite. The wardrobe is approx. 2.97m long. Scope of Work: Dismantle & Move On-Site: Carefully remove 3 floor-to-ceiling sliding mirror doors and their top/bottom tracks. Safely carry mirror panels down 1 flight of stairs; stack neatly on the ground floor. Strip out internal white melamine shelving, upright partition panels, and drawer runners. Note: Internal framing is nailed directly into walls/floor, not screwed. Please use a pry/crowbar to minimise drywall damage. Stack all timber neatly. Drywall Patching: Patch and flush-repair the rectangular drywall cutout/hole shown next to the skirting board in file. Patch any holes or surface tears left behind by framing nails. Optional Disposal: If selected, remove all timber, tracks, and mirror glass from the property. Requirements: Bring own tools (pry bars, track removal tools). Supply own plastering/drywall patching compounds. Must be physically capable of safely moving large mirror panels down stairs.

Need these 2 driveway ramps drilled screwed into the ground. 4-6 screws each. So it stays put

Storz & Bickel VEAZY - Dry Herb Vaporizer Looking for an experienced electronics hobbyist or bench technician with micro-soldering capabilities (fine-tip iron, flux, and ideally a microscope setup) to repair a high-end dry herb vaporizer. The Device & Materials:Model: Storz & Bickel VEAZY (a premium, German-engineered medical-grade device). Casing Material: The outer shell and internal structure are made of medical-grade PEEK plastic (Polyether ether ketone). This is a highly heat-resistant engineering polymer, but it is tightly sealed. It needs to be pried open gently with proper plastic opening tools without snapping the plastic tabs or melting the housing during solder work. The Issue:The device has an internal connection failure. I need a technician to open the PEEK casing, inspect the main logic board, and re-solder the broken joint. This is likely: Option A (If not charging): A fractured pin connection where the USB-C charging port meets the PCB board. Option B (If not turning on): A loose/snapped power wire connecting the single-button system or internal battery to the motherboard terminal pads. Important Note on Warranty:Please note that I am deliberately choosing to bypass the official manufacturer warranty process due to the long turnaround times for international shipping as well as not purchased in Australia. Because opening this device permanently voids my warranty coverage, I need someone meticulous who will treat the board with care, apply proper flux, and ensure there are no bridges or short circuits before re-assembling. Logistics:I can drop the device off to you if you are located around the Campsie / Inner West / Canterbury-Bankstown region, or you can here. Please offer your price based on a quick bench diagnostics and point-to-point micro-solder reflow.