Find a sockets and switches installation professional in VIC

Looking for electrician to modify light switches of a wall partition build. Date: Monday, 8 June 2026 Time: Strictly 11:00 AM onsite Location: Campbell St, Epping (just behind Epping train station) Scope of Work: Split 3-Gang Switch: - Convert existing 3-gang switch into a 2-gang switch (stays in current position). - Relocate the 3rd switch to a new back-to-back partition wall (approx. 90cm away). Relocate 1-Gang Switch: - Move an existing single light switch to the reverse side of the same wall (approx. 10–15cm away). Site Conditions:All walls are plasterboard / gyprock (hollow cavity). Requirements: Provide a Certificate of Electrical Safety (CES) upon completion. Please bring all necessary cables, plaster brackets (C-clips), and standard white plates.

Install several downlights, remove/change switches. New lights are 90mm. Old lights are smaller and directly wired. Quote for 10 downlights 4 switches. I have new lights and switches.

I tried to replace/fix my light switches and I broke them. 4 switches that turn on 1 light only 2 of them work now. And my garage lights don't work anymore.

We have 2 sticky light switches. We purchased the switches thinking we could get my uncle (licensed electrician) to install. He’s now travelling so on AirTasker it goes.

Looking for a fully licensed, insured A-Grade electrician to complete a residential final fit-out. The rough-in phase will be fully completed before this task begins. All cables will be sitting ready at the plaster cut-outs with standard mounting brackets fully installed. I will supply 100% of the visible faceplates, mechanisms, and smart modules. The primary wall gear is brand-new Hager Finesse in Matt White. Scope of Work: Install, terminate, and test the following hardware items. (Base quantities listed below; final counts may vary slightly by 1-3 items on the day). Powerpoints: 44 x Double 10A GPOs (WBQP2S-MW) Pre-Assembled Push Button Switches: 20 x 1-Gang | 4 x 2-Gang | 3 x 3-Gang | 5 x 4-Gang | 1 x 5-Gang | 1 x 6-Gang (Note: All 34 plates will be handed to you fully pre-assembled by me with their internal wire-tail LED modules snapped into place. You only need to wire the tails into standard Locator Mode—so the LED stays ON when the switch is OFF). Cooker Isolation Switch: 1 x Hager 1 Gang Horizontal Rocker Switch (WBQCKSH1-MW). Smart Modules: 4 x Shelly Smart Relay Modules to be wired directly behind 4 designated wall plates. Active, Load, and Neutral connections will be roughed-in and ready at these 4 boxes. Data & TV Outlets: 10 x 1-Gang Plates containing a mix of 8x Cat6 Data Mechs and 2x F-Type TV Mechs (All mechanisms pre-installed into the plates by me). Requirements: - Valid A-Grade Electrical License and Public Liability Insurance. - Supply standard trade consumables for termination (wire connectors, tape, etc.). - Test all circuits and issue a compliance certificate / Certificate of Electrical Safety (COES) at handover.

Need 3 power point on the internal wall plus need hole in the cabinet side board for washing machine connection

fixing 3 light switches that are stuck and do not work

Change power plugs and split switches for lights

Looking for a certified electrician to do the following. At this point looking for a quote to see if it meets my budget. x7 power sockets x2 pendant lights (to replace existing oyster lights in kitchen) x11 down lights (replacing oyster lights) x1 wall sconce in bathroom.

Remove two light switches and install two new light switches.

I need 4 light switches to be fixed as they are a bit flaky. It doesn’t switch on immediately and requires some fiddling around with the switch.

Relocate three light switches to nearby wall.

Hi there, I am currently doing some home renovations and need a licensed electrician to update the connections for 5 existing LED wall lights. Current situation: There are 5 old LED wall lights (70mm cut-out). Their LED drivers are currently hardwired into the mains behind the plasterboard. What I need you to do: • Remove and safely disconnect the 5 old hardwired LED drivers. • Supply and install 5 standard surface sockets (plug bases, e.g., Clipsal 413 or similar) at these existing points. • Push the new sockets back into the wall/ceiling cavity safely. Important details: • No new wiring or cutting new holes is required. The 70mm holes and the wiring are already there. • I will supply and plug in the new downlights myself once the sockets are ready. You only need to supply and install the 5 surface sockets. • You must be a fully Licensed Electrician and be able to provide a Certificate of Electrical Safety (COES) upon completion. Please let me know your availability and your quote for the complete job (including the supply of the 5 sockets). Flexible with dates but prefer to get it done soon. Thanks!

Existing Clipsal switches and power plugs Replaced with new Clipsal Iconic Switches. No new connections required. There are around 35 power plugs, and around 20 switches to simply be replaced. The 4 switches includes existing dimmer and fan - these are existing and simply to be replaced with new Clipsal. All items have been purchased and ready to be replaced.

Looking for a licensed electrician to replace 6 existing light switches with Clipsal Saturn Zen (or other) switches. The current switches are older push-button style and some buttons are sticking. I want them replaced with the newer Saturn Zen versions. Scope • Remove 6 existing switches • Supply 6 x Clipsal Saturn Zen push-button switches (Zen White) • Install the new switches • Test that everything works correctly Switches will be paid separately (please supply them and include the cost of the switches in your comment so I can reimburse) 2 x 4 1 x 3 1 x 1 2 x double power point

3x power plugs and 1x power switch need to be replaced in home

Hi I'm looking for a registered electrician to fix a couple of electrical sockets. Based in West Footscray

i need 3x deta smart light switches changed to 3x normal deta switches. smart switches are playing up. i have purchased new switches. location - sandhurst 3977 vic

I need Electrician to change some lights and switches in two bathrooms First Bathroom - one room has become two rooms, additional switch and light, fan heat light in the new room, Second bathroom, two rules have been combined and one switch is required, light fittings supplied by me, Replacement of free in one heater light and fan, relocation of another fan,

On/off switches for two power switches are loose (don't flick on and off cleanly).