Find a local Tasker to help you make a kitchen cabinet in Melbourne

We’d like to modify our kitchen cabinets to fit a compact domestic washing machine. Kitchen Cabinet Opening 690mm high (780mm internally, opening could be cut at least 30mm at the top and more below if we cut out at the bottom shelf) 635mm wide 560mm deep (with more space behind the rear cabinet, this is likely the most limiting factor at the moment) The existing doors are fine, no need to modify them. Ideally we only want to make modifications to the internal carcass to fit the following target dimensions: 600–620 mm wide × 850–860 mm high × 600 mm deep. So width is fine. Height is the major issue: we need roughly +160–170 mm. Depth is slightly tight: ideally gain 40+ mm, or allow the machine to project behind the cabinet's rear carcass (there is a cavity behind it). Would also be great to have someone with plumbing/handyman experience to organise the plumbing from the existing sink to the new washing machine area (inlet splitter and outlet join to existing waste water).

Cracked laminate on single cabinet door only. Needs to be replaced. Laminex gloss panel (Formica - Snowdrift)

A kitchen cabinet door - perspex - about 114cm high (so a bit heavy and bulky) needs to be rehung on 3 existing hinges - we have the fixing screws. The cabinet is above a benchtop. There are two other kitchen cabinet doors where the hinges need adjusting and another hinge on a laundry cupboard that needs to be re-clipped.

I want to add kitchen cabinets in front of the exhaust fan. I want the door to hide the fan. I’ve attached images

There are a number of broken and loose hinges in our kitchen cabinets. There is one with a completely broken corner door hinge. Another corner door hinge that are loose. And one that has come out of the internal carcass entirely due to the screw holes being threaded.

I have a fridge which stands in a kitchen cabinet and the fridge door has became unattached- the piece that holds them together has broken. Can you fix it please?

shorten kitchen cupboard and build a small frame

I have a kitchen cabinet door that needs to be cut down to a smaller size

We have a tall kitchen cabinet we’d like to reconfigure with an oven & microwave and use the rest of the space with drawers under the oven and a cupboard above the microwave. Can the existing door be used for drawer fronts and cupboard door? The hob is only 2 rings and we’d like to make space for a larger one. We also have a very heavy drawer under the bathroom sink that needs better runners to cope with the weight.

Kitchen required to be altered so dishwasher can be installed. Dishwasher to go under sink area. New single sink installed.

I have a kitchen cupboard which needs to be cut down to size. We have recently purchased a new fridge and require the cabinet above the fridge to be cut.

I am looking for a professional to remove an existing kitchen cabinet unit (containing 2 drawers as shown in the images) to create space for a standard dishwasher. I require a good quality finish and am particularly concerned about ensuring no damage is caused to the surrounding cabinetry during the removal process. Please provide an estimated quote for this work.

Repair two kitchen cabinet draws and tighten loose ones. May require new Front Fixing Brackets for Drawer Slides & self closing standard single wall drawer set. See photos carefully.

1) Remove old kitchen bench, draws and cupboards. 2) Build and install IKEA kitchen draws, cupboard, dishwasher alcove 3) Cut sink hole and fit into benchtop 4) Drill hole for mixer tap and fit to bench top

I will be available all morning tomorrow for an appointment to view the property and work necessary for quote Had to buy a fridge as the old one finally failed. New didn’t fit into the fridge cavity of our built in cabinets. I took out and replaced the floor with a thinner board. Reassembled and complete screwed it up. Need inspection and then estimate to fully repair Estimate given here purely a guess.

Recently completed a kitchen renovation with new shaker-style cabinet doors installed. Looking for someone experienced with kitchen cabinetry or joinery to fine tune the alignment on two small overhead cabinets (4 doors total — two side-by-side cabinets with two doors on each). A few of the door reveals/gaps are slightly uneven (approximately 1–2mm) and I’d like them adjusted for a cleaner, more consistent finish. Likely a straightforward hinge adjustment job. Photos attached.

I need an experienced cabinet maker, IKEA fitter, or flat-pack specialist for a labour-only job. This involves removing two existing cabinets and the old laminate benchtop, shifting one cabinet to its new position, and assembling and installing two new IKEA METOD cupboards with a new laminate benchtop. All materials will be supplied by me once measurements are confirmed. SCOPE - Site visit & measurement sign-off - Remove old benchtop and two existing cabinets and shift one existing cabinet to new position - Build and install two new IKEA METOD cupboards - Fit new laminate benchtop across full layout and add cutouts for induction and sink Current and proposed layout attached.

I am looking to install a standard size dishwasher (ideally Bosch Series 6 Freestanding, linked below), however the existing kitchen cabinetry needs to be revised to fit a dishwasher. Kitchen cabinetry is standard melamine. Images/measurements of the space attached to the posting. More photos/measurements can be provided if needed. I believe the countertop can remain at its existing height, right side outer edge of the cabinet in the same position, with the inner cabinet walls removed at the top/bottom and sides (aka fits into the “pink” space illustrated), with a hole cut for hosing. The biggest change needed is to the depth of the cabinet space so the dishwasher isn’t sticking out the front. Open to ideas for what might look/work best, but ideally the back of the island looks cohesive. Potentially adding extra storage underneath (see image with “blue” where back of dishwasher would need to be concealed and “red” where extra cabinets or something could be). Please let me know if you have any questions or need any other information to provide an accurate quote. Dishwasher Model: https://www.appliancesonline.com.au/product/bosch-serie-6-freestanding-dishwasher-sms6hci02a/

Kitchen Pull Out Pantry does not fully extend. It gets stuck. Make - Sige Art 255K 120Kg.

Please note: Work required in MAY. I am undertaking a renovation and the Kitchen cabinetary is being reused at another house. The job is to carefully defit the cabinets so they are preserved for refit. There is: 1 x Island with 2 x 3 drawers, wooden benchtop needs to be cut at the edge of the drawers as it wraps around a corner 2 x Floor cabinets with 3 drawers - wooden benchtop to be kept 2 x Glass fronted overhead cabinets