Find an experienced cabinet maker in WA

I need a sheet of plywood 244Ommx 122Omm x 12mm jigsaw cut into a shape. See pic of shape

I would need to replace one front drawer and one small door cabinet

Can someone please make a bookshelf the same as this and deliver to Eglinton I don’t have the timber Preferably 1.4 long x 1m

Cubby hole in the wall previously used for microwave and oven. Have bought a double oven for the space. Need to level and raise the floor of the cubby hole (exposed bricks) to allow the new oven to be fixed in space (towards the top). Will need skirting/lining on the outside edges once oven in place for aesthetics

Laundry kitchen and linen press cabinets all stripped back all plumbing disconnected ready

I need to make some cabinets and desks for the building

Looking for an experienced cabinet maker or carpenter to replace water-damaged internal cabinet boxes (carcasses) under a double kitchen sink. The exterior doors, handles, benchtop, and surrounding cabinets are intact and will be reused. Measurements: Width including the carcass as shown in photos is about 997–1000 mm. Height as measured in the photo is about 727–730 mm. Depth as measured in the photo is 557–560 mm. Scope of Work: Measure & Fabricate: Supply and build new internal cabinet carcasses using High Moisture Resistant (HMR) board/melamine to fit the existing space. Open back cabinets are acceptable. Removal: Safely remove damaged particleboard sections (under-sink floor, damaged middle shelf, lower drawer box area, and center support mullion) without disturbing the benchtop or sink. Installation: Fit the new HMR cabinet box/shelving, including neat cutouts for existing plumbing pipes (drainage pipe and water inlet lines). Reattach: Re-hang existing white cabinet doors, align hinges, and re-fit the bottom drawer runner/front. Damage Details (See Photos): Water damage from a previous leak has caused the particleboard base, middle shelf, and center support post to swell, split, and crumble. 3 internal lower sections and 1 bottom left drawer space need rebuild/re-boxing.

Looking to redo my laundry. I can’t use ready made cabinets due to a curved wall. After a quote for something nice but fairly basic too. Will attach pictures of current setup and what I hope to achieve

After a cabinet maker or someone with qualified skills to create these custom made trolleys. Looking for a beige colour but image as a guide. Are you able to source materials and custom make these for salon use? Let’s talk

I need a cabinet maker to build and install kitchen wardrobe and vanities and entertainment unit cupboards. All standard carcasses Blum or hafele

I’m looking for a carpenter or cabinet maker to build and install custom sliding pine doors for an angled loft / roof storage space. The opening is approximately 800mm high x 2300mm wide. The finished result should look similar to the reference photos attached, with clean timber / pine sliding panels across the front of the storage area. The job includes: • Measure and confirm the opening on site • Build a simple framed opening for the storage space • Build and fit sliding pine / plywood doors • Install a floor rail / sliding track system • Add a suitable top guide or support if needed • Build side return walls / end panels where required • Make sure the doors slide smoothly and are easy to remove or access • Finish neatly so it suits the existing pine-lined ceiling and loft area The space is under an angled ceiling, so the job will need someone comfortable with custom carpentry rather than standard flat-pack cabinetry. I’m after a practical, neat storage solution, not a high-end wardrobe finish. Happy for the doors to be made from pine ply or similar material, provided the final look is clean and simple. Photos attached show the actual space and examples of the finished result I’m aiming for. Price is for labour. I will pay for the materials you need to collect from Bunnings etc and give me receipt. Please include materials, labour and track hardware price roughly in message.

Hello, I'm looking for someone with experience in cabinetry, built-in wardrobes or joinery to finish an IKEA PAX wardrobe install to make it appear built in and a tidy finish. Scope of works 1. Install infill/filler panels • Fill the gaps between the wardrobe and the side walls with 16mm MR MDF. • Scribe the panels to the walls where required so everything sits flush. • Ideally use moisture-resistant MDF or similar ready for painting. 2. Install a kicker/plinth board • Cover the existing timber base with a neat kicker/plinth with either 16 or 18mm with 16mm MR MDF. • Continue the plinth across the full width so it appears built in. • Minimise visible joins. 3. Finishing • Light sand and prime final cut and fitted pieces • Colour match GRIMO door at Dulux trade centre • Ideally, paint with low sheen Dulux Aquanamel and using high-density foam roller to achieve sprayed-looking texture • Finish neatly against the existing skirting boards and also IKEA base (may require some filling of gaps above plinth / kicker) • Caulk as required. Notes • Wardrobe is already fully assembled and secured. • Photos attached showing the areas to finish. Please only apply if you've completed similar built-in wardrobe or cabinetry work. Photos of previous jobs would be appreciated. Cheers,

Need 2 extra drawers added to my dressing table similar to the ones in the bathroom (see photo) and another cupboards doors changed. (Shortened to cupboard height so I can keep them closed when not in use but still have the counter space below the second shelf) At the moment my microwave on the counter comes out to far so the doors can’t be used. Don’t look at the budget. I have no idea if costs so after quotes..

Storage cabinet in cavity. Width 110cm Depth60cm Height230cm Plenty of shelves Gloss white

I have 2 wardrobe recesses. 1 master and 1 small recess. For now I just need a hanging shelf in both. White 20ml thick shelf? with pine wood supports underneath and a heavy duty silver pole. I will pay for materials extra. Other work available 😊

Looking for a cabinet maker to built some custom cabinetry around the farmhouse sink and washing machine. Have a 600mm purpose built cabinets for the farmhouse sink. Need narrow cabinet (or frame) built to right so counter top can wrap around. Some work on the farmhouse cabinet needed. And then supply and install timber top (or laminate timber bench top) around the farmhouse sink and over the washing machine. Wall length is 1350mm

Require a cabinet maker to measure and quote for 3 panel melamine doors under staircase. I have attached a photo of my staircase currently with nothing underneath and also attached photos of what I would like it to look like

I'm looking for a cabinet maker/joiner to design and install a custom pantry in my kitchen and someone who installs cabinets in a laundry room please

Carpentry / custom wardrobe cabinetry work, to add rails and shelves into inbuilt wardrobes, in white melamine. Two wardrobes of 2-3 meters each. We can evaluate design requirements, depending on cost.

Hi there I am working on a new clients home and need some cabinetry made and installed. Please include photos of work you have completed in your offers or comments. Thank you