Find an experienced cabinet maker in VIC

Need to make cabinet in garage

Order and install Polytec cupboards x4 418 x 756 x 18

Our current kitchen need an installation of a built in fridge. We need a cabinet maker to extend the current cabinet but a few centimetres to fit the width of the fridge and also built the door panels.

Need cabinet maker in spotswood

Cut out a space for a dishwasher under bench in an existing kitchen cabinet. Still need to maintain the appearance of the kitchen. I want to be able to have the remaining cupboard space under the sink as well so a small door or a blank can be installed between the edge of the dishwasher and the next door. Pillar will need to be moved across. I have some photos with the measurements. Dishwasher is 820mm high, 600mm wide and 570 deep. Parking is off street (I have a driveway)

Looking for a cabinet maker to make a countertop with small sink, dishwasher and washing machine in this space

Need cabinet in existing kitchen

I have heavy cupboard door and hinges need replacing as they are failing. I have replacement hinges that are heavier duty. Would require removal off old hinges replacement with new and adjusting so there is cupboard closure. Approx 10 cupboards approx 30 hinges

Existing kitchen cabinets has to be redone for the dishwasher installation.

Need to build 2 cabinets for the below spaces - Above the Fridge - Below a cooking table. Photos are provided for these spaces. Please provide me your best quote.

Install Murphy bed and build cabinetry around it

Hi Guys, need a experienced cabinet maker to install some Cabinetry. Wardrobes, laundry, vanities. Let me know which. One you specialise in and i can forward drawings based on your experience and preferences. Start date 13th April. Most Cabinetry comes pre assembled, the wardrobes are flat packs and tall cabinet like pantry is flat pack.

I recently removed our door panel that usually covers our fridge, because its a bit of a nuisance. I would like to repurpose it to cover the areas around the fridge. The panel is Kaboodle oak latte (melamine faced particle board). I would like someone to measure and cut: 2 x smaller cabinet doors (to go above the fridge) 2 x long vertical strips (to be used either side of the fridge) I would also like the door hinges to be repositioned and installed for the 2 doors. I’ve attached photos to show the existing setup, and a mock-up of what we’re hoping to achieve for clarity.

Wardrobe needs to be removed for repairs behind then put back the next afternoon 195cm x 125cm

I need two wooden tops cut to fit a computer table spot and below the tv. Also have 3 doors made to cover 3 spots, as shown in pictures.

G'day all, I'm looking for a cabinet maker to help me with a small kitchen project. What I'm needing is a cabinet box made up and fitted above our fridge in the kitchen. We have the doors and shelves, but for some reason.. the cabinet box has gone missing ( dont ask haha). Of course the job will need to be measured up, box made, and box fitted, which I'm happy to help with if required. Box measurements approx as follows: Height: 550mm Length: 950mm Depth: 400mm This job would ultimately suit someone who has no dramas doing the quick small jobs, and you'll be well payed for your services. As you can see I've just put a small amount on the job listing, so I can leave it to you to tell me how much you need to get it done👍 Cheers all Cam🍺

Need two extra shelves in my pantry. I have already purchased some melamine shelving that needs to be cut down and fit to size. I have availability for this today and tomorrow Each shelf needed approx 565mm wide and 540mm deep, shelving purchased is as per photo Will need holes tapped for shelf holders that I have purchased too.

Need my laundry redone a cabinet maker to make bench and cupboards looking for measure and quote

I am looking for a qualified cabinet maker to inspect and correct kitchen cabinetry that was installed incorrectly by a previous contractor. The work involves checking all base cabinets to make sure they are level, square and structurally ready for 20mm stone installation. It also requires confirming that the overhead cabinets are properly fixed into studs and reinforcing them if needed. Some doors, drawers and panels need realignment so the kitchen is safe, stable and compliant before the benchtop is remeasured. This is not a job for a handyman. I need someone with formal cabinet making qualifications, an ABN registered for cabinet making or joinery, and experience preparing kitchens for stone installation.

I need a qualified cabinet maker or handyman with cabinetry experience to come out and adjust the cabinets around my laundry washing machine space. The current cabinets are slightly uneven/misaligned, and I’m unable to slide the washing machine into the space. Task details: • Adjust/straighten existing cabinets so they sit flush and aligned • Ensure the washing machine space is the correct width and clearances • No major rebuild required—just adjustments to allow the machine to fit properly • Bring any tools needed for small cabinetry fixes (e.g., hinges, screws, levelling tools)