Find a local welder near you

There is a kids ride on car whose front tyre suspension rod has become loose and needs welding to fix it. I can bring the car over to welder's place or feel free to come, whatever works

i have a small rust hole on the body when you open the RHS rear door i want the rust cut out and metal welded in. it doesn't have to look good, as no-one will ever see it. see photo.

Panel beater welder around boot front and back windows back corner Panel

Looking for a skilled and experienced automotive welder to install an aftermarket sports muffler onto an existing exhaust system. This is not a beginner job — only apply if you have proven experience with automotive exhaust work and can deliver clean, durable welds. Job details: Weld on a 2.25-inch inlet sports muffler to existing exhaust piping Ensure proper alignment and fitment with exhaust hangers fabrication may be required to achieve correct positioning and clearance Must ensure no leaks, rattles, or poor joins Requirements: Must have your own tools and equipment (including jack/lift if needed) Experience specifically with automotive exhaust welding Ability to complete the job to a professional standard Price is negotiable

I have a Conqueror UEV310 camper trailer with the early model rubber suspension axle, which is seized. Rather than replacing it with a new rubber suspension axle, I want it to be converted to leaf springs. I will buy a leaf spring kit meeting the requirements of the trailer. I need you to remove the old axle and install the new axle. Removing the old axle is straight forward. To install the leaf springs, a steel mounting plate will be required. The steel plate needs to roughly 60mm x 900mm x 8mm. The leaf spring mounts are welded to the plate (I expect professional welds!), the plate is then bolted to the trailer frame (needs new holes drilled) with 4 high tensile M12 bolts and self locking nuts. The leaf strings and axles are then mounted to the above plate. Also, you may need to weld the brake bracket to the new axle depending if this is done already from factory or not. Of course, everything as to be straight to and aligned. I buy all the required suspension parts and hardware. You do the labour and provide a welder and whatever other tool you require to complete the job. The mounting bracket can easily be fabricated on a workbench ready for installation, before the trailer gets pulled apart. I cannot help, make sure you have a helping hand if you need one.

There is a small crack in my van's firewall, affecting the master cylinder. It's too small a job for a mechanic to do - should be a quick job. My mechanic said I just need someone handy with a welder to help get it fixed.

Middle muffler delete Vy v6 Can bring car to you

The starter motor from my Nissan Navara YD25 is disassembled and I have new brushes and brush holder and need two brushes spot welded to the stator. The old brushes are still in place and will need to be removed. I will reassemble and test.

Small welding job on a 1995 Hilux sub-frame to repair some rusting. The job has been prepared, the replacement metal plate is cut to size and ready for welding (MIG ideally)

Would like some g80 bmw seats fabricated into my fg falcon, custom seat adapter made up. If possible wired up so the work too

Need weld back panels and side panels thin car panels together I have Mig welder if required

I need 2 x 25mm aluminium bungs tig welded on to 2 x intake pipes. This is for a turbo set up in car. Must be welded to a high standard, clean welds with no leaks. Prefer mobile welder.

Need help fixing misaligned exhaust on Audi A5 (DIY install gone slightly off) I’ve installed a custom exhaust but the rear hanger doesn’t line up properly with the mounting point, causing the exhaust to sit off-centre and tilt to the right. As a result, the exhaust tip is touching/melting the rear valence. Looking for someone experienced with exhaust work to: • Realign the exhaust so it sits centred in the rear bumper cutout • Adjust or modify the hanger (bend or reposition as needed) • Ensure proper clearance from the bumper (no contact) • Secure everything properly so it doesn’t move or rattle No welding required if possible, but open to it if needed for a proper fix. Car: Audi A5 3.0 TDI

I need a water tank mounted onto the truck , photos of location required and water tank is attached. the mud guard bracket will need to be bent square and re welded

Electric car seat part broken weld.

Looking for someone experienced with exhaust welding to help with a small exhaust modification on my 2011 Hyundai i30 wagon. Work needed: • Install a factory rear muffler from a Hyundai i30 hatch onto my wagon • Weld in an electronic exhaust valve dump pipe before the muffler that exits behind the front passenger wheel • Relocate or adjust exhaust hangers if needed • Connect the electronic valve (simple power wiring) • Make sure everything is mounted properly with clean welds I already have the muffler and valve. Located on the Gold Coast but can bring the car to you if nearby. Looking to get it done ASAP.

Wanting to fit a valve in the midpipe of my exhaust, then a boom tube connected to the valve. I can do the wiring myself for the valve, I just need someone to weld it or source one I can clip on. For a bmw f30 N20

Front steel bar just need welding.

Bracket Chassis Welded on Jeep Wrangler

Front end of au falcon damaged from a crash, we are going to cut a frame from a different car and cut the frame off the damaged vehicle and we need someone to line up the frame and require someone weld it onto the damaged vehicle unless someone with experience has a better idea.