Find skilled builders in North West Perth

Exposed aggregate to match existing drive up to boundary and road, apps 12 m2

Replace existing metal roofing on front garden pergola with clear/translucent polycarbonate panels. Pergola is approximately 5.0m long x 2m wide on a timber frame in good condition. Remove and dispose of existing metal roofing and all waste. Supply and install clean polycarbonate sheets with UV protection, flashings and appropriate fixings to suit timber frame. Ensure waterproofing and neat finish; seal and trim penetrations. Please include options and expected warranty. Accessible from ground and ladder; no structural repairs required potentially need additional support beam to prevent sagging. Price negotiable

Looking for an experienced licensed builder/structural carpenter to widen an existing opening and install a Lotus Doors Glas-Stax Frameless Weather Defence moving glass wall system between our living and outdoor areas. The complete Glas-Stax system is already on site. Scope: Remove existing sliding doors. Demolish approx. 1m of adjoining brick wall to widen opening, with clean saw-cut to remaining brickwork. Remove/dispose of debris. Temporarily prop existing roof/patio structure during works. Supply/install structural steel posts/columns and required footings/anchors. Supply/install engineered steel lintel/beam above opening. Structure must be accurately level, rigid and suitable for the Glas-Stax overhead track. Install and align Lotus overhead track. Install, align and calibrate glass panels, seals and floor guides to Lotus specifications. Make good surrounding areas as required. Details: Lotus Glas-Stax – Frameless Weather Defence Panel height: approx. 2.8m Opening width: to be confirmed on site. Please quote for demolition, structural works, steel/materials and installation. Must have appropriate licensing and public liability insurance, with experience in structural alterations, large openings or architectural glazing preferred.

Oil Leak on the drive way

Small garden shed with skillion roof (Model ES-S1523), dimensions 1.51m x 2.25m x 2.1m. 4 walls & roof panel already pre assembled but may need some reassembly to gain a better fit.

Easyshed assembly down side of house

Clean, prime,fill in cracks, paint drive way and porch roughly 17mx6m Paint, primer supplied

Flat packed shed needing assembly 2X3, and bolted to bricks .Located Sinagra

Hi I have a brick driveway that a cement sewerage access lid on it. The cement lid is angled and doesn't line up nicely with the bricks. I need someone with brick cutting expertise to make it look presentable. I have spare bricks, just need someone with a brick saw and skill. Cheers

Looking for an experienced concretor to assist with pouring and finishing a driveway and garage slab. All materials, mesh, concrete, formwork timber, will be provided. Driveway: 35m x 3.5m Garage: 3.8m x 6.4m Passage: 10m x 4.5m For some extra details please see bottom corners of first picture Please quote your rate and confirm: • Your availability • Any photos of recent work

Looking for an experienced concretor for pouring and finishing a driveway and garage slab. All materials, mesh, concrete, formwork timber, will be provided. Driveway: 35m x 3.5m Garage: 3.8m x 6.4m Passage: 10m x 4.5m For some extra details please see bottom corners of first picture Please quote your rate and confirm: • Your availability • Any photos of recent work

Looking for an experienced concretor to assist with pouring and finishing a driveway and garage slab. Driveway: 35m x 3.5m Garage: 3.8m x 6.4m Passage: 10m x 4.5m For some extra details please see bottom corners of first picture Please quote your price and confirm: • Your availability • Any photos of recent work

Need to insatall a Garden shed which is 3.00×2.26×2.00m +slat fence gate which is 1065×1750 mm

House has been rebuilt and we need Distribution board installation with Plunking under driveway for mains for our house and the existing rear house behind (it's a duplex) Our builder wants this done asap

I Have purchased a shed 6 x 3.75mt and i am looking for an installer to assemble the shed

Elderly mother needs beams replaced if possible or this section of pergola fixed. Photos included.

Renovating ensuite, bathroom and laundry and need toilet, cabinetry and tiling removed - floor and walls. Minimum dust is really important as asthmatic in house.

Looking for someone to assemble a Stratco Handi-Mate Sliding door shed (1.86m wide, 0.85m deep and 1.90m high). It also comes with a shed floor beam kit that needs to be fitted. It will sit on pavers and no need for anchoring. This will be behind the house in a corner. Area will be cleared prior to the assembly.

Help to Dissemble a 3×3m - mimosa louvred pergola. I bought online, mert at sellers house in Nollarama today. Please bring: Drill, ratchet set, Hand tools, Ladder, I dont know if bolts in concrete need sawn off, if you have grinder also would be useful. Work involves, undoing lots of Nuts/bolts each louvre, screws/Allen keys to undo fram connections. Its Aluminum frame, so careful not to thread. (Its happened before ). I can assist with my tools also and have a 1 x collapsable platform ladder. I would like your help to load into/onto my Van roof racks also. I'm 1 hr drive from location. So rbc a time with yourself and the place picking up from. Need completed Today. Thanks you

There is a bunch of rubble, gyprock, old wardrobe panels and general demolition waste that needs to be gathered up and placed in the skip bin on site. I estimate about two hours work for one person. There is a wheelbarrow on site to make this easier.