Find a professional staining service in Sydney Eastern Suburbs

Cut a new piece from a new tile. Install tile using silicone tile adhesive

If you are a stainless fabricator with suitable offcuts, this could be a good small job. Do you have any 304 brushed stainless offcuts large enough for three small benchtop sections and a splashback? I need supply, fabrication and installation I have a very small kitchen and would like to cover the existing benchtop with 304 stainless steel, plus cover the existing tiled splashback with matching stainless steel. This is a rental property, so I want something very hard-wearing, practical and easy to clean. Approximate benchtop sizes There are 3 separate sections: Note sink part has to have all sides covered . * Sink section: approx. 135 cm long * Cooktop/oven section: approx. 70 cm long * Back section with no cut-outs: approx. 142 cm long Depth is approximately 60 cm, but all measurements are rough. You will need to measure properly before fabrication. There is an existing sink and cooktop that need to be worked around. Splashback I want the existing tiled splashback completely covered with 304 stainless steel. I would prefer the stainless splashback to match the benchtop. It’s approx 60 cm high Not urgent happy to wait anytime you have a time

I need my garden deck sanding and restraining - approx 40sqm.

3x4m deck 3x1m side 3 x stairs

This deck is sun weathered and needs to be cleaned with oxalic acid, or the like, sanded back a bit and stained with oil, we will supply oil.

Hi I have a spot in my living room where rain has leaked into the room. I think my ceiling is 3.6m high but I dont have a ladder tall enough. I was looking for a handyman to try and clean as much of the residue as possible.

Parts of the carpet with stains need to be replaced I have extra carpets- so we would need to cut out the stains and put new carpet in

Recently bought a table and bench but the colour is slightly off so it needs sanding and staining then assembly. Assembly should be v simple just legs that need attaching

Need two 2700 x 1200 Oak Veneer Plywood sheets stained a rich dark walnut colour with semi gloss finish. Similar to below. Oak Veneer European Oak Brushed Crown Cut Raw Please quote me

Hi there, I need an experienced professional to completely restore my outdoor timber deck and a small set of stairs. I want to keep the natural, raw light blonde look of the timber and completely avoid any dark golden or orange tones. Project Details:Size: 5m x 5m deck (approx. 25 sqm) plus 1 small set of 3 steps. Timber Type: Spotted Gum hardwood. Current Condition: The deck is currently dirty, weathered Scope of Work Required: Prep & Clean: Apply a dedicated timber cleaning agent (e.g., Intergrain UltraPrep/Cabot's Deck Clean) and thoroughly scrub the deck to remove dirt, graying, and tannin buildup. Nail/Screw Punching: Inspect the entire deck and punch all raised nails/screws at least 2mm below the surface so they do not tear sanding pads. Sanding: Sand the main deck back to fresh bare wood using an orbital floor sander. Detail sand the edges and the 3 steps. Important: Sanding must stop at 80-grit to ensure the dense Spotted Gum pores remain open to absorb the oil. Coating: Thoroughly stir and apply 2 coats of a non-orange, blonde-tinted penetrating timber oil (such as Cutek Extreme CD50 with a White Wash tint pack, or a pre-tinted light oak option). What you need to provide:You must bring all your own trade equipment, including a commercial floor sanding machine (orbital sander preferred over a aggressive drum sander), hand/detail sanders, extension leads, a stiff deck scrubbing broom, and high-quality lambswool/microfiber oil applicators. You will supply all the necessary consumables, including the deck cleaning chemical, the 80-grit sandpaper discs, and the 4L/5L tin of specialized blonde timber oil. Please share examples of your previous timber decking or sanding work when bidding. If i like how you work I will then also need sanding of my backyard deck much bigger job. Thank you!

I need one mirror and two pieces of artwork to be hung onto a concrete wall with the heaviest item being 9kg in weight. I require you to drill into a concrete wall and supply and install three stainless steel screws and plugs please.

Build a set of flat pack 12 lockers . Should take maximum an hour

My existing wooden deck is in good condition and needs to be restained.

I have 2 wall mounted shelves that need to be fixed in the bedroom. 10kg each 1845 x 495 x 100 I also have a box I need opened with a tool, see picture for detail

- Full sand back + stain + seal - Approx 54m² - Includes fixing scratches as much as possible (see close up pictures attached) - Experienced floor sander preferred

I have a 2m high x 1.6m wide freestanding outdoor mirror made from 45mm x 45mm angled stainless steel. I would like to mount it to a wall and to do this I need to have tabs welded to the sides, bottom and top of the mirror frame. I have 9 mild steel tabs made up to weld onto the back of the mirror frame, 2 each side and top and 3 at the bottom. Because the mirror is so large, this is something that I need to get done on site.

Two doors with total 3 breaks in stained glass. Please provide materials and repair.

TITLE: Floor sanding, staining & polishing — residential home Note - work won’t commence until July We're looking for an experienced floor sanding and polishing professional to sand back, stain and finish the timber floorboards throughout our home. The existing floorboards are currently a light/natural timber colour and we need them taken back and restained to a significantly darker tone to match new flooring recently installed in other areas of the house. WHAT WE NEED DONE: • Full sanding of existing floorboards (multiple passes to remove old finish and open up the grain) • Application of a dark stain to match our existing new flooring — we're happy to provide a sample or photo for colour matching • Application of a quality oil-based finish (e.g. Loba, Bona, or Rubio Monocoat) for durability and a rich, deep look • Edge sanding and corners • Clean-up of all dust and debris on completion ABOUT THE SPACE: • Approx 100 m² across multiple rooms — including 3 bedrooms, office, living, dining and hallways • Wet areas (bathrooms, laundry, kitchen) are excluded — timber floors only • Standard single-storey home — easy access • Timber species unknown — tradie welcome to assess on inspection Please provide a quote that includes all materials (stain + finish coats). We'd love to see examples of dark stain work you've done previously. Prefer a fully licensed tradesperson with public liability insurance.

You will need your own sander, oil/paint and materials. 4x4m wood deck. It's in good condition (as in no rotting), but needs a sand to remove some left over mould and then to oil. As we seem to have a few days of sunshine, I'd like this done ASAP. There is plenty of parking and I might be able to get you an undercover park too. There is a lift to the floor then one flight of internal stairs. An easy job but needed before Wed 15th April. Thanks

Stain the fence posts. Will provide stain and brush. Front fence (one side), side fence (both sides).