Find a professional staining service in Fortitude Valley

Looking for an experienced metal/stainless-steel fabricator to measure, fabricate and install a custom folded brushed stainless-steel surround over an existing aluminium shopfront window frame. The existing glazing and aluminium frame are to remain in place. The new stainless-steel surround will fit neatly over the existing frame to give it a high-end architectural finish. Approximate specifications: - Existing frame: 2400 mm wide × 2600 mm high - New surround face width: approx. 100 mm - Projection/apparent thickness from wall: approx. 10 mm - Material: brushed stainless steel - Exposed outer edges to have a soft pencil-rounded finish - Corners to be cleanly mitred - Fixings to be concealed wherever possible - Consistent brushed grain direction and premium finish - Fabricator to recommend appropriate stainless-steel grade, sheet thickness/gauge and fixing method - Site measure required before fabrication - Supply, fabrication and installation required The attached image shows the existing frame on the left and the intended finished appearance on the right, including a detail of the required corner/edge finish. This is a visible shopfront feature, so quality of fabrication, mitres and finishing is important. Please only quote if you have experience with architectural stainless-steel fabrication. Please include supply of all materials, fabrication, delivery and installation

We have 3 small deck areas with spotted gum timber decks that were professionally sanded and stained 12 months ago. They said we wouldn’t need sanding again if we stained promptly at the 12 month mark. Deck staining product will be provided in new tins as we already purchased the same product that was used last year. Just need someone familiar with fully washing and then applying the appropriate number of coats of stain to the decks neatly and professionally to protect them for summer.

Metal Fabricator Needed – Brushed Stainless Steel Wrap for Existing Shopfront Window Frame. Job Description Looking for an experienced metal/stainless-steel fabricator to measure, fabricate and install a custom folded brushed stainless-steel surround over an existing aluminium shopfront window frame. The existing glazing and aluminium frame are to remain in place. The new stainless-steel surround will fit neatly over the existing frame to give it a high-end architectural finish. Approximate specifications: - Existing frame: 2400 mm wide × 2600 mm high - New surround face width: approx. 100 mm - Projection/apparent thickness from wall: approx. 10 mm - Material: brushed stainless steel - Exposed outer edges to have a soft pencil-rounded finish - Corners to be cleanly mitred - Fixings to be concealed wherever possible - Consistent brushed grain direction and premium finish - Fabricator to recommend appropriate stainless-steel grade, sheet thickness/gauge and fixing method - Site measure required before fabrication - Supply, fabrication and installation required The attached image shows the existing frame on the left and the intended finished appearance on the right, including a detail of the required corner/edge finish. This is a visible shopfront feature, so quality of fabrication, mitres and finishing is important. Please only quote if you have experience with architectural stainless-steel fabrication. Please include supply of all materials, fabrication, delivery and installation in your offer.

I have a stainless steel strainer/press used in a commercial kitchen. One of the support brackets has broken off at the welded joint (left side in the photo). The other side is still attached, but the weld looks quite weak as well. Would it be possible to: * Re-weld the broken side * Remove and re-weld the other side properly if necessary, so both sides are secure

Sand back my staircase that has 14 steps and then restain it a darker caramal colour to match floorboards and seal.

I need a Stainless Steel welder today if possible to cut and fix a couple of legs supporting a stone bench. One is too long and the other too short. You may need to supply tubing.

We need a professional welder to add a stainless steel angle/strip along the front edge of our existing café sink bench to help push water back into the sink and prevent drips onto the floor. Details: • Location: Fortitude Valley, Brisbane • Task: Supply and install stainless steel angle (approx. 8mm height) along bench edge, as shown in photos and sketch • The strip should be securely welded (preferably TIG) to the existing stainless steel countertop • Must be food-safe finish, neat and durable • Purpose: Stop water from dripping over the edge when washing items • Photos and diagram attached for reference • Work to be done on site during cafe closed hours or quiet time Please bring all necessary tools and materials. Experience with commercial kitchen stainless steel fabrication/welding preferred.

Needing a small hole cut into our stainless steal bench. Need done on site. Located Fortitude Valley. Photo is reference for what we need done

- kick boards to be replaced - reflective strip to be installed - timer to be sanded down and restained

My son had a squeeshy ball and during the summer it must have fallen down the side of his bed and stuck to the carpet. I have tried using nail polish remover and it doesnt change anything, I need to get rid of this without ruining the carpet as im in a rental. They are probably a bit bigger than 1 dollar coin in size, its really just the orange that needs to go. Thanks for your help - Due date: Before Thursday, 23 March 2023