Experienced Handyman needed for silicone refresh in shower alcove & minor crack repairs as well as a few other odd jobs (4hrs hours) Remove old silicone and replace to ensure all gaps are fully covered to ensure no leaks get through. Description: Budget is $350. Port Willunga Tuesday 27th would be ideal 👌

We need someone to remove the existing silicone, eradicate the mould in the grouting underneath, and then re-seal with new silicone. This is a shower-bath so there is silicone on three sides where the bath meets the wall.

We need some assistance with removing old degraded silicone and applying new silicone in our shower. This would include around the base, between the shower screen and in the corners of the walls. We do not need new grout, this is the silicon component only. We’d also like some general advice about the shower base, to make sure it’s all okay. We purchased the house and shower like this. Happy to treat with bleach first or whatever is recommended.

Remove and replace silicone around bath tub and tap. ~ 10 meters total Material provided

Looking for someone experienced to professionally remove silicone and reseal the floor waste/drain in a tiled shower. The existing silicone around the square stainless-steel drain fitting is deteriorated and needs replacing. Scope of work: 1. Carefully remove the existing deteriorated silicone around the square drain fitting. 2. Clean and prepare the surfaces, removing old silicone residue. 3. Inspect the surrounding joints for any obvious deterioration or movement. 4. Apply high-quality, waterproof, mould-resistant sanitary silicone suitable for stainless steel and tiles. 5. Use charcoal/dark grey silicone to match the surrounding grout. 6. Ensure a neat, professional finish with clean, straight edges. Important considerations: - The shower floor has large-format charcoal tiles. - Care is required when removing old silicone to avoid damaging the tiles, drain fitting or underlying waterproofing. - There is some existing white filler/sealant around the circular grate. Please inspect this and advise whether it requires attention. - The job is for surface resealing, not replacement of the drain or waterproofing membrane. - Please advise if you identify any potential waterproofing concerns before proceeding. Requirements: - Previous experience with bathroom/shower silicone sealing. - Supply all materials and tools.

Remove shower stall, regrout, clean up, waterproof - regrout essentially Note that $10 is not my budget but just a placeholder - happy to discuss with a quote in person or in chat.

Reseal shower base as old looks bit mouldy

The shower silicone needs replacing. I removed two sides already but havent removed side 3, side 4 doesnt have silicone. The bottom 2 sides have not been removed yet. This task involves removing the silicone properly, and replacing it. I have materials already provided. Before 15th October or after 24th October.

Reseal 1 shower silicone. Thanks

1 x SHOWER refresh required - Shower floor area: approx. 1600 mm × 800 mm -Thoroughly clean and prepare all surfaces before application -Remove old, discoloured, mouldy silicone where required and apply new mould-resistant, watertight, bathroom-grade silicone -Leave most grout as is but regrout sections that are cracked (see photos). I believe the previous tiler (5 years ago) used epoxy grout. -To use own tools and supplies. Professional finish

Looking for someone to help reseal one small section of silicone around a bathroom door frame where there is a minor gap. Just needs to be cleaned and resealed neatly with bathroom-grade silicone. It’s a small and straightforward job.

Silicone in bathroom and/or minor grout repairs, including removing mouldy silicone. Supply all materials and tools.

Need to reseal the base of the shower as it was poorly done previously.

Need an experienced bathroom sealing/waterproofing professional ASAP. I attempted to remove some mouldy silicone and reseal the shower myself, but the seal has failed and water has leaked through, so I’d like it fixed properly. Job includes: * Remove the failed silicone seal along one side of the shower (approx. the length of the shower). * Clean and prepare the area thoroughly. * Apply a professional-quality, mould-resistant bathroom silicone. * Check for any gaps that may allow water to escape and ensure the shower is fully watertight. It’s only a small job (one long edge of the shower), but I’d like someone with experience in bathroom sealing rather than a general handyman. Please bring all tools and materials.

The Silicone Sealants in both bathrooms of the unit have blackened and are to be completely removed and resealed. The task is for quote.

After someone to re-silicone the joints in my fully tiled shower. The old silicone has gone mouldy and stained and needs replacing properly. Scope: - Cut out and remove all old silicone: the vertical wall corners, the wall-to-floor join, and the glass screen base (both inside and outside, the outer join has mould too) - For the vertical corners, full height is likely overkill, so if cutting out just the affected sections is enough, that's fine - Once the old silicone's out, treat the exposed joints (bleach or mould remover is fine), then rinse - Degrease the joints with methylated spirits so the new silicone bonds cleanly - Let everything dry fully before resealing (fine to leave it overnight between strip and reseal) - Apply new mould-resistant silicone with a neat finish Details: - Fully tiled shower (ceramic floor and walls, glass screen), base roughly 90cm x 175cm - Must use premium anti-mould silicone such as Maxisil, Mapei, Soudal etc. - Photos attached

Need the shower re siliconed. Removal of old silicone and new silicone done. To match grey and cream colours currently.

Floors in tow small bathrooms have been resurfaced. Old silo was dug out at the time. New silo needs to go around floor edges and shower floor. Grey color ideally. Each bathrooms approx 1.8mx3m

Looking for an experienced tiler or silicone specialist to remove and replace the silicone around the perimeter of my shower base. The silicone was replaced about two weeks ago, but it wasn’t properly prepped and the finish is not very neat. I have already removed one section to allow me to clean. Scope: * Remove existing silicone around the shower base perimeter * Thoroughly clean and prepare surfaces * Remove any mould or residue as required * Apply a neat, professional silicone bead I can provide the silicone. Please only respond if you have experience with bathroom silicone work and can provide a high-quality finish.