Find professional garden shed repair in South West Sydney

Small garden shed, drill and wrench needed. Build inside garage

Task Description: Looking for a reliable person to assemble a new Keter Darwin 6x4 plastic garden shed. The work is located in. Video : http://www.youtube.com/watch?v=dfq4rz80Mgg Key Requirements & Steps (Detailed Scope of Work): Step 1: Land Preparation (Critical): Step 2: Shed Base Assembly: Connect the two-part plastic base and secure it with the initial screws once the ground is level. Step 3: Panel Installation: Slot in the ~20 plastic panels, including corners and back pieces. Step 4: Roof Assembly: Assemble the two-piece roof with the strengthening bar and center joining strip. This part requires perseverance and detail to ensure it is watertight. Step 5: Door & Hardware: Install the two doors, including the hinges and the locking mechanism, which can be a bit fiddly and requires manual assembly. Correct ground leveling is essential to prevent doors from misaligning. Step 6: Fixings: There are hundreds of screws involved in this build to fully secure the joints and the base. Keter Storage Shed Shelf Kit × 1 needs to be installed inside at the end Tools Needed: Shovel/Rake/Levelling tool (for land prep). Electric Drill/Driver (highly recommended due to the large number of screws). A ladder for reaching the roof panels. Additional Details: Location: [ Austral/Sydney NSW 2179] Timing: Flexible, but would prefer completion in a single session, given the sequential nature of the ground-to-shed build. Pro-tip from the video for the Tasker: If you find the hinge holes difficult to line up, try driving a "pilot" screw in and back out first to clear the path. Please also ensure the outer door trims are perfectly aligned so the doors shut correctly.

Looking for someone to build a garden shed in Sydney. - I already have the shed just nerf to build. Please message me with your experience, availability, and quote. Thank you.

Need to assemble the garden shade from Big W. Pls see the photos or the link for details re sizing etc. You can check the link. Floor concrete already exist. https://www.bigw.com.au/product/giantz-garden-shed-1-62x0-86m-sheds-outdoor-storage-tool-workshop-house-shelter-sliding-door/p/9900116310?utm_source=google&utm_medium=cpc&utm_id=22282771902&utm_campaign=BIGW+Market+%7C+Shopping+%7C+Lawn+%26+Garden&utm_term=&gclsrc=aw.ds&gad_source=1&gad_campaignid=22282771902&gbraid=0AAAAADkZkLjBTmXHLbbT0DhxCXYh_B9oW&gclid=Cj0KCQiAqeDMBhDcARIsAJEbU9QgCFlSbh81saIAy1lsJUAxTzYXQFp5RXQ_a4gpnP7P8G3aiErUIy4aApvTEALw_wcB

I want to construct a concrete 2x3m slab to install a garden shed in by backyard.

3.75m x 0.78m Narrow Slider Garden Shed With Concrete Fixings 8pk & Corner Flashing 4pk

3m wide x 1.5m deep x 2.1m high gable roof garden shed to be build. Base is already there and I will help with positioning.

I need an experienced handyman to assemble and install an EasyShed metal garden shed. Shed details: • Brand: EasyShed • Size: 2.25m x 1.5m • Roof type: Skillion roof Site details: • Installed on an existing concrete slab • Anchoring to the concrete base is required • Easy access to the backyard • All shed parts are on site Requirements: • Prior experience assembling EasyShed or similar metal sheds • Please bring your own tools • Job to include full assembly and anchoring Looking for someone reliable with good reviews.

I bought garden shed and done the job of little of it. I need the garden set up as earliest possible. Please see the below image for information.

Setup concrete slab for base 3.1m x 2m Supply & Install garden shed Shed size required 3m (L) x 2m (D) x 1.8m (H)

The pop rivets have popped out from centre roof and side wall and needs securing.

Hi I am looking to install a custom garden shed in my side backyard length 4 meter width around 82 cm.

Assemble garden shed from bunnings

Have an Easy Shed Garden Shed to be assembled over a pool pump, will need a hole saw to cut one small hole in a side panel to allow for a suction pipe and it has concrete bolt kit with it. https://easyshed.com.au/products/garden-locker-shed-2-08m-w-x-0-97m-d-classic?srsltid=AfmBOoobCyTOrCuiTi3KjCzxLaE2mKj7iBz9Qc68fz1fGsbxd0-pD3a3

To install a garden shed with window on a cement faver. 2.25x2.25,quote pls

Garden shed panels already assemble only require to put it up. The size of the shed is 2.2m W x 0.78m D x 1.98m H.

Looking for an experienced shed installer / handyman to assemble a Stratco Handi-Mate AS Deluxe hinged door shed. • Shed kit is onsite and unopened • Base is already prepared and level (see photos) • Easy access • No slab or groundworks required Important: Must have prior experience assembling metal garden sheds (Stratco / Absco / similar). Please include photos of previous shed builds in your offer. My brother is quite particular, so attention to detail is important.

The new slab is now a triangle shape, back wall, one side and front will remain the same dimensions one side and roof will need to be modified to fit.

We need a timber floor base/deck constructed 3x2.25M for the purpose of installing a garden shed (supplied) in our backyard. Required ** 1. Timber for base 2. Tools of trade 3. Previous experience doing similar work

To install a garden shed on concrete