Find trusted local electricians in Augustine Heights

Power outlet chandelier, power points weather proof

Hi, can you please provide me a quote for replacing 12 down-lights with its plug sockets and replace an AC fan. All materials will be provided . Location Augustine Heights. Looking to finish it by Friday 3rd April.

1. Change over double general purpose power outlet x2 2. Change over quad general purpose power outlet x 1 3. Install led wall light x2 4. Replace led wall light x 2 5.install led weather proof spot light 6. Replace ceiling fan 7. Replace standard chandelier x3 8. Install weather proof general purpose outlet x1 9. Install downlighting fitting x2 Need few new light fittings, new power point, changing the ceiling fan and power ports, installing new chandeliers x3, Prefer someone to give me an on-site quote. Easy to explain the scope of work. Thanks

Need electrician work to be done at my place outdoor for some lights and fixes

We have three lights that we want to replace. All three are located at the front of the house. We already have three Lucci lights. The job involves removing the existing lights and installing the new ones.

2 wires have snapped off plug and i need them wired back into plug

two of them Just need replacing for the current non working and 3 new installation. I need a certificate. the location is Springfield central. I have the fans so I just need The work done

Dig apprx 2 metre trench at min 600mm for electrical cable and partially dismantle concrete block retaining wall about 3 metres down 3 courses.

We have some solar powered downlights in the living room and garage. Only the garage light is turning on while rest of the lights sometimes flicker but do not turn on

I need two pigeon nests removed from under solar panels and then I need the panels to be bird proofed. I have the mesh and clips ready to go, I just need labour done. It is a 1 storey home with a twenty panel array on the roof. I’ve put the lowest budget required as I would rather wait for quotes

I need an electrician for a quick job. To install 1 dinning light and ceiling light. The ceiling light is in the void area, will need a tall ladder.

I require my light bar electrically connected, I have it already mounted on the vehicle and have a harness. I'm in Augustine Heights

Electrician to install 4 down lights .

Need an electrician to install an external power point for a pool and spa pump . Not sure what’s involved but has to be able to support 2 pumps (pool and spa) there are power outlets nearby but I don’t know if they can be utilised for the use or not .

outdoor electrical blind is stack

Split ac installation in small room .

I need someone fabricate a flat mounting system on top of existing solar panel rails on my roof to hold moving head spot lights. The rails have been installed and I need a horizontal flat base setup to sit 4 x moving head lights on top. It needs to be level so the lights sit flat/straight. Each light weights 25kg and can be held by the rails. I was thinking just some marine ply and timber studs to attach to the solar panel L shape brackets. I just need it to last for the next 3 weeks in the weather on the roof. The spot lights will be 1 metre apart from each other, so was thinking of two platforms built to hold 2 each rather than spanning the entire roof section. They do have threaded bolt holes in the base but was thinking this would be difficult to bolt to the timber platform. Was thinking of using just straps to hold it down but they are 25kg so doubt they will move at all. I assume two platforms of 1200mm x 500mm. The solar panel rails are installed one tile width apart from each other. I would like this done asap.

I need to replace a downlight as it is currently flickering, I have purchased a new downlight which is a plug in, but unfortunately the one that was installed is wired in and does not have a plug so cannot replace on our own.

Daikin 8 Zone Ducted Unit controlled by my air app, on a single level house requires service. 1 Zone not working, all other 7 Zones working fine without issue.

I need someone fabricate a flat mounting system on top of existing solar panel rails on my roof to hold moving head spot lights. The rails have been installed and I need a horizontal flat base setup to sit 4 x moving head lights on top. It needs to be level so the lights sit flat/straight. Each light weights 25kg and can be held by the rails. I dont care what it is made out of but it would be good if it was aluminum as it wouldn't rust. In the below photos, the red box is my draft of something that needs to be built