Find trusted mechanics in VIC

I need some one to installed and it’s a Apple play unit / head unit , also a spot lights on the front of the van ,

Motorbike clutch adjusted properly an engin inspection coz there’s a clicking sound I duno wot it is

Brake pads will be provided along with sensors. Just need the front and rear brake pads replaced

Install a new head unit. In a C3 Corvette. -Trim the plastic fascia for the new head unit. (Must be confident to be able to do this so that it is neat and without causing damage. -Install the new head unit so that it is installed properly and secure. -Connect the new head unit harness to the car wiring, so that everything works (Must be confident that you’re able to figure out which cable does what) -Connect the speakers (2x 6” in the dash and 2x 6x9” in the back) -Wire up the electric arial so that it goes up and down when the radio is turn on/off. -Test everything to make sure there are no issues. Additional info: -The interior of the car is stripped, so all wiring is easily accessible. -The old original head unit was working, so the wiring should be ok. -I have access to the wiring diagram for the car. -I have installed a new electric aerial but I believe that the existing relay needs to be bypassed to connect it ( I have a video on what needs to be done, but I need someone that will be able to work out how to make the arial go up and down when the radio is turn on/off, if the instructions on the video doesn’t work) https://www.youtube.com/watch?v=X0OL5h4sDNo

Mazda3 2008 Oil and filter provided

Apple play head unit installed 2008 Toyota Kluger

Seeking a AC regas for my Hyundai i30 preferably onsite at my residential home in Cranbourne North. Ample easy parking. Seeing a mid service with compliance documents. Regas and leak test only-cabin filter dosnt need replacing Please advise what your price will include. Seeking job to be done in the next couple of weeks Blower motor working fine

Hi - I am looking at installing a head unit/radio & Front & Back hardwired dash cam for a Tiguan Pacific 2013 model. Details of the head unit: https://gtzone.com.au/products/volkswagen-tiguan-2008-2014-9-inch-wireless-carplay-android-auto-head-unit-navigation-bluetooth-wifi-head-unit?_pos=1&_psq=tiguan&_ss=e&_v=1.0 Details for the RGB to CVBS (RCA) AV Converter: https://gtzone.com.au/products/vw-camera-rgb-to-cvbs-rca-av-converter?_pos=1&_psq=converter&_ss=e&_v=1.0 Details for the Dash Cam (Hard Wired): Q200 | THINKWARE Australia GPS: GPSANT DASH CAM GPS ANTENNA | THINKWARE Australia Can you please quote? Need another quote for a second Dash Cam hard wiring install only for a Kia Cerato

HYUNDAI ACCENT 2016 NEEDS OIL AND FILTER CHANGE +BASIC SERVICING

I need to have the oil and filter changed on my car today at 4 p.m. at my home.

Open to quotes and flexible with time thanks

In middle of oil change but can’t get sump plug off as can’t find the correct socket Car is jacked up in garage, has Liquimoly engine flush in it so not drivable Car is Mercedes Benz 2014 A200

Currently have a stereo connected to an amplifier. However the wiring is extremely messy. Would like this cleaned up. The amplifier is sitting loose as well, so would like this mounted somewhere out of the way, such as under passenger seat etc. The cable tied wiring runs at the feet and up the centre of the passenger seat. Can take more pics if required. In addition, winch is not powering on so would like someone to look to see why, and ideally have this fixed if it can be. If it can't be, would be good to have someone there that can also install. Car is a Land Rover Discovery Series 1. Can also meet in East Doncaster if easier. Or drop car off if not too far from Abbotsford.

I have a 2008 530i BMW and I’m interested in having the unit installed

Head unit install and reverse camera

Need experienced mechanic service 2 cars – must follow exact oil change method. Oil and filters Supplied Description: Looking for someone to do an oil and filter service on 2 cars. This is not just a normal quick oil change. I want the job done exactly to a specific method step by step, so I need someone who is careful, patient, mechanically minded, and happy to follow instructions properly. Please only apply if you’re confident doing the below exactly as requested: Required oil change procedure: 1. Start with the engine completely cold. 2. Add about 1 litre / 1 quart of fresh oil to the existing oil as a pre-flush. 3. Start engine and let it idle for exactly 5 minutes. 4. Turn engine off and wait 10 minutes. 5. Then drive the car 10–15 minutes to full operating temperature. 6. Park on level ground, let it idle 2 more minutes, then drain the oil immediately while hot. 7. After the first drain, leave it for 30 minutes, then remove the drain plug again and do a second drain. 8. Fit new oil filter, but pre-fill the filter to about 60–70% with fresh oil first. 9. Apply a thin film of oil to the rubber gasket and hand tighten only. 10. Refill engine slowly with about 80% of oil capacity first. 11. Wait 5 minutes, then top up slowly in small amounts, checking the dipstick each time. 12. Final oil level should be around halfway between low and full, not overfilled. 13. After refilling, do not start the engine straight away. 14. Turn ignition on without starting, wait 10 seconds, then turn it off. 15. Repeat that 3 times. 16. Then start engine and let it idle for exactly 3 minutes without touching the accelerator. 17. Check for oil leaks around drain plug and filter. 18. Turn engine off, wait 2 minutes, then re-check oil level and top up if needed. Must Have • has experience servicing cars, or is very mechanically capable • has their own tools • works cleanly and carefully • is happy to follow this exact process, not their usual rushed method

Brand new bull bar Location in hawthorn I can be their to help lift the bar in place

Need a qualified or experienced mechanic to replace rear brake pads on a Mazda CX-5. • ✅ Parts already supplied • 🔧 Labour only required • 📍 Location: Yarraville • ⏱️ Timing: Within the next hour (urgent job) • 🚗 Vehicle is ready to go Should be a straightforward job for someone who knows what they’re doing. Please bring your own tools. Prefer someone with experience in brake work.

While topping up engine oil , I added more oil than required. As shown in picture. So it's well above the maximum mark. Although I don't see any immediate problem, I would like to remove excess oil and just keep to the mark. I don't require change of Engine oil or any other services...just extract excess oil. Vehicle:- Honda Accord 2006 model ivtec.

Need two light bars attached to Dmax Bullbar (Ironman bullbar). Need them wired in so I have a switch in the cab to turn them on or off. Or at least so they go off when I flick to low beam while driving on the road.