Find professional pool gate repairs near you

We have a frameless glass pool fence, about 15 yrs old. The glass gate swings on a top pivot fitting and a stainless steel floor-mounted spring/pivot box set into the paving. The hinge mechanism is failing and the gate needs repair. What I need: - inspect and identify failed part - repair or replace it - make sure gate self closes and latches with pool safety compliance Please only apply if you have experience with glass pool gates and floor spring/pivot systems. Please include your quote.

Automatic close is broken, I need someone to supply and fit a new closing hinge and it needs to hit WA’s standard of self closing pool gates

Buy pool hinge from Bunnings and remove old hinge /install new hinge pool gate. $240 ($200 + $40 for hinge) https://www.bunnings.com.au/truclose-self-closing-pool-gate-safety-hinges_p4150114.

Pool gate attached to timber post has sagged and needs adjustment to fix vertical gap and level top

My pool gate does not automatically close when it’s ajar. I think the hinge needs to be tightened, I’m not sure how to do it

Hi, I’m looking for someone to repair a pool gate at my property in Mount Waverley. The gate post is wobbly, causing the gate not to self-close and self-latch properly. This was identified during a recent pool safety inspection. Could you please let me know your availability and approximate cost to fix it? Thank you.

Gate is fixed to house with brackets, one of which is quite close to conduit. Side panel has spigots concreted into a narrow flower bed close to a retic pipe. Ideally the concrete will be dug out and removed with the spigots. If this isn't possible without damaging the retic the spigots can be cut below ground level so the upper parts of them can be removed as long as the parts remaining in the ground are made safe (ie, not sharp). Access is via a side gate (app 1 m wide) on the other side of the house or via a narrow walkway and through the rear garage door.

Install pool gate door on side pathway of house. I have the pool gate, 2x gate hinges, pull gate latch and 2x posts. I dont have screws at base of post that needs to be fixed to tile.

Out gate pool latches have moved (as they are secured to wooden decking) and no longer automatically close. I think it is just a matter of re-adjusting them but I can't seem to do it.

Requires a mew spring. We don’t have time to do this. Require someone to source a new spring and install for us. It is a glass pool gate. We are just speculating as we have had a maintenance guy take a quick look and mentioned this and that he could do it easily then he went missing so haven’t had it finished. Need it done tomorrow if possible.

Finish installation and adjustment of pool safety gate I’ve attempted to repair and reinstall our metal pool safety gate, including replacing the hinges and MagnaLatch, but haven’t been able to get everything aligned and fitting correctly. The gate is back on its hinges, but it needs some final adjustments to the positioning and alignment, and the MagnaLatch needs to be properly installed. One of the screws has also been damaged during installation and may need replacing or extracting. Looking for an experienced handyman or pool fence installer to finish the job, ensure the gate swings freely, self-closes and latches securely, and meets Victorian pool safety requirements. Most of the work has already been done, so hopefully it’s a relatively straightforward job for someone with the right experience. Photos attached.

Two pool gates don’t fully latch from up close. Need to tighten and adjust pool gate hinges or latches to pass council inspection.

Pool gate, wooden slatted gate, circa 6 ft. height, has failed local council pool inspection as it does not close automatically (the full way). Gate does not close fully, so seeking someone that has experience in either installing a hydraulic arm or any other ideas. Based in Doubleview/Scarborough, looking for the job to be done ASAP. Please respond how you would do it also.

We urgently need a pool gate/fence specialist to repair our pool gate safety mechanism. The gate is not locking/latching properly. It currently requires extra force to close it firmly enough for the latch to engage. If the gate is simply swung open and released, it does not reliably self-close and lock. This is an urgent safety issue as there multiple children regularly at the property, so the pool gate needs to reliably self-close and self-latch every time. Job required: * Inspect the pool gate, hinges, latch and self-closing mechanism * Identify why the gate is not automatically latching * Adjust/repair the mechanism and gate alignment as required * Replace the latch/closer/hinge components if necessary we will cover additional cost if needed * Test the gate repeatedly from different opening positions to ensure it reliably self-closes and latches * Please ensure the repair is suitable for Victorian pool barrier safety requirements Important: We do NOT just want the gate to latch if it is slammed or pushed hard. It needs to close and latch automatically when released, without manual force. Urgency: ASAP – preferably today/tomorrow. Location: Hampton / Bayside area Budget: Approx. $150–$200 for labour/repair, with additional cost for parts if required. Please advise if you think replacement hardware will be needed. Please only apply if you have experience with pool gates/pool fencing and self-closing/self-latching mechanisms.

replace swimming gate, glass, 900 x 1200 mm back into stair well. Needs new holes for same supports and old holes disguised. ...can give a hand to lift the glass gate ...fittings are the same

I need to replace pool gate hinges and have a small part of fence reattached to post. Flexible

We need a pool gate fixed It is not closing properly

My two pool gate latches will not automatically stay. I am out of ideas how to fix myself. Need to get fixed asap.

The pool gate isn't latching as the bottom hinge is out of alignment. Job is to fix this so the gate latches and is compliant

We have a pool gate that has sagged slightly, so now doesn’t close properly. Original installation didn’t include all screws, so guess that has impacted it. Need it to be taken down and reinstalled properly so it auto closes and latches per compliance regulations. It has the right auto close hinges etc.