Find an experienced driveway repair contractor in VIC

Supply and install gate with backing plate to driveway. Black aluminium or Colourbond. Our space is 3580W x 2100H at the narrowest part from the house. Otherwise we are also considering having it sit further back from the house which is 4650W x 2100H I am guessing it’ll need to be two swing doors, unless we can do 1. There is power to the right of the house to allow for a swing motor. Also on the left hand side I am thinking there will need to be a fixed panel there due to the brick wall sitting off the fence. Have attached a photo for reference.

Driveway wall to be painted same colour as house. Paint will be supplied.

We’re looking for an experienced drainage plumber or landscaper to inspect and quote installation of a strip (channel) drain along the side of our house where the driveway slopes inwards. Our restumper recently advised that water is tracking under the house after rain, likely flowing across the driveway toward the subfloor area. We’d like a drainage solution that captures this water and redirects it safely to stormwater drains. Job scope (to be confirmed on inspection): • Cut and remove a narrow section of driveway beside the house • Install a suitable grated strip drain or channel drain • Connect to existing stormwater line or discharge point • Ensure correct fall for water flow • Restore driveway surface neatly once complete Driveway type: Paved/bricked (see photos) Location: [Coburg, VIC] Access: Clear access along side driveway Please quote for works (happy to arrange inspection first). Must have relevant experience in surface or stormwater drainage.

I need someone to paint the driveway. Driveway has already been painted but it has few patches. All driveway to be painted and paint supplied by you.

Looking for quotes to get an exposed aggregate concrete driveway done. Measurement is 29sqm

Driveway gate needs some holes drilled so latch can fasten properly. It has bolts currently but they don't stay up when opening and closing the gate. Job is to install new fastners if needed and drill holes if needed to make the gate easy to open and stop moving when open

Hi, Hope you’re well. Looking to get a quotation for a motorized gate for our single driveway and front path. I’ve attached some photos of our property for reference and one inspiration. We’re based in Bentleigh East, VIC. Kind regards, Daniel

Removal of dead palm tree branches and leaves. Already cut and placed on our driveway for easy collection. Sharp bits of palm tree branch have been cut off for safer handling.

I’ve attempted to install a Milkcan clothesline on my sloping concrete driveway, but I’m struggling to get the post level both ways without using packers that end up showing and making it look really bad. I’d rather have someone professional do it so it looks perfect. • Clothesline posts need to be cut down so the final installed height is approx. recommended height is 1,800mm, but I want • Posts must be securely fixed to the concrete using the supplied mounting plates. • Driveway is on a slope, so everything needs to be leveled properly for a neat finish. Alignment to the roller door needs to look square if you look down it. I’ve already drilled 4 holes for the first plate and put a few screws in so it needs to be fiddled with. Additional Note: I’ve already drilled one hole, but it’s 12mm when it should have been 10mm. The end of a bolt has dropped into that hole. You’ll need a strong magnet (which you can bring) to fish it out. After that, the hole will need to be neatly fixed—either gluing a bolt in place or another suitable method. What’s Provided: • Clothesline, mounting plates, bolts, and standard accessories. What You Need to Bring: • Tools for concrete drilling/fixing • Saw/grinder for trimming posts to the right height • Strong magnet for retrieving the bolt • Any adhesive or filler needed to repair the oversized hole Level to make it square and aligned

Smashed light off driveway wall, needs to be replaced. I will provide the same light

The bottom of one double swing driveway gate is damaged - metal frame and the drop bolt got bent. Can you fix it? If we need to replace with new ones, please let me know how much!

I've finished construction of a bike shed, I need someone to anchor the shed to the concrete driveway. It requires around 16 anchors to be driven into the concrete.

Pressure wash outer concrete area (no driveway).

Pour a concrete strip footing for driveway gate

Removal of concrete from driveway approx 6.2m x 2.5m (concrete slab thickness approx 8 cm. Plus removal of bricks approx 1.8m x 1.4. You will need to bring all required tools and dispose of concrete/bricks. (Optional - level soil in preparation for new driveway)

Driveway gate has been incorrectly hung. Will need new heavy duty hinges. Gate will need to be raised and rehung to open outwards.

Looking for someone to pressure wash: • Pebble concrete driveway • Front path • Concrete foot path on both sides of a corner block I need a solid clean-up to get the place looking ready for sale. Someone who has had experienced in pressure washing a pebble concrete area and understands how to do this safely required. Power and hose access available.

I need this area excavated and soil taken away. 150mm deep 7.2x3.8 Mentone