Find a sockets and switches installation professional in SA

Hi, I need a licensed electrician to replace 2 light switches in my unit in Klemzig. Scope: • Replace 1 × 3-gang switch( button loose- still works) • Replace 1 × 2-gang (outside cracks works fine) • New switches already purchased • Existing wiring in place- no issue with the switches • Straight swap job Requirement: • Must be a licensed electrician • Must provide Certificate of Compliance after completion Happy to negotiate Location: Klemzig SA Flexible timing after 6 pm

Task: Replacement of two faulty light switches. Details: • Laundry switch: Currently stuck in the “on” position and the light won’t turn off. Needs replacement. • Hallway switch: Also requires replacement (not functioning properly). • Both switches are standard light switches. What I need: • A qualified electrician to supply and install two new switches. • Ensure both switches are safe, compliant, and working correctly after installation. Location: Laundry and hallway inside the home. Preferred timing: Flexible — anytime that suits within the next few days.

I got lan cable installed previously from one room to another but the wall sockets has telephone ports. I need to update the wall sockets to cat6 sockets. The cabling is anyway cat6.

Replace existing switch with smart switch and replace 3x worn switches

Add 2 sockets include one for a small oven (max 2000KW), one for ranghood. Can use existing wire under the benchtop for old oven (old oven has been removed)

add 3 sockets in the kitchen including move one socket lower, and add two new sockets (the area is near current airconditioner )

Rough-in: • Run cabling and cut holes for approximately 16-20 LED downlights in: • Main living areas • Kitchen/meals • Hallway • 3 bedrooms • Any extra wiring required for new/relocated switches and outdoor lights. Fit-off (after painting): • Supply and install LED downlights in all prepared locations. • Replace any old oyster lights as agreed. • Update a few light switches and powerpoints to modern white units. • Install 2 LED batons under the pergola and upgrade entry light

Installation of lights (2 x sconces) with individual light switches

I need to replace 25x light switches. Currently have clipsal but a lot of them jamming. Need to replace them with regular black switches. 9x 3 switches (vertical) 8x 2 switches (vertical) 4x 4 switches (square) 4x 1 switches

We have 2 light switches in our house that are currently broken. Needing someone reliable, reasonable pricing and no added cost after quote. Electrical certified and DHS required.

I have 4x 3 gang push button light switches I just need someone to put in the led bulb into them. I was able to do the single and double gang as didn’t need to remove the mech from the switch. Also have a single gang need doing but needs some electrical work as when the led bulb gets put in the light stays constant on.

Hi Im looking for electrician to install 4 power sockets at my house. Thanks

Need 15 Amp socket and 10 Amp socket in my pergola for Radiant heater . Cable to run from main switch board to pergola which is around 15 mtrs

I need approximately 5 wall sockets for power. Unsure if theres cableing in the walls has light switches that work

About 10 push pull switches (marked) and wire into new switches Remove old gauges and wire new ones Also wire new bilge pump

I have 3 lamps where the shade has broken the lamp socket cradle. So I need these 3 replaced. 2 are table lamps and one is an old floor lamp.

Require supply & repair/replacement of 2 light switches/plates located in lounge and toilet. Room A -> Clipsal 2-bang with dimmer (32E400M) : Top rocker (connected to down lights) is broken - requires replacement. Bottom rocker works OK. Room B -> Clipsal 2-bang | Both rockers faulty (connected to light and fan in toilet). Can intermittently get both to power up if fiddling with switch - rockers appears faulty. Both plates are cream / beige in colour. I get a sense this colour might have been discontinued from what I can find on the web (Clipsal). If rockers of this colour can't be sourced, a white plate & switch replacement for all is fine. Also appreciate diagnosis of fan in Toilet once switch is fixed. Can hear it buzzing but unsure if spinning correctly. Need to determine whether motor is blown.

I would like to run wiring before gyprock 3 switches, 4 power sockets and and 3 lights

I have a number of Electrical jobs around the house including replacing lights … perhaps installing downlights … might need new light switches … installing fire alarms … surge protector … as well as connecting electrical wiring for a newly installed gas hot water system (installed by a plumber years ago, but needs electrical connection). The unit is located outside the house. Have been making do with extension cords :(. Keen to have a chat and see what you might suggest …

To replace 2 old WS226 to new ones，and I already have them，just need to connect the wires.