Find a local Tasker to inspect your Mazda in Melbourne

I'm looking for an experienced mechanic to replace the head gasket on my 2009 Mazda 3. The issue has already been professionally diagnosed by my local garage. A leak-down test confirmed the head gasket has failed, with leaks in cylinders 1 and 4. The car is still drivable and can be driven to your workshop, but it's started to splutter, so I'd like to have it repaired as soon as possible. Please provide: Your experience with Mazda head gasket repairs. A quote for labour (and whether you'll supply parts or if I should). Your availability and estimated turnaround time. Located in Northcote, VIC.

Service on my Mazda 3. 20213z Engine light is on. I can bring to you

2008 Mazda 3 Maxx Sport BK Series 2 hatch (build 04/2008), 2.0L petrol, manual, halogen (no HID). VIN supplied to accepted tasker for parts ordering and paint code. CORE JOB - driver's side (RH) front headlight: - Supply new aftermarket ADR-compliant RH headlight assembly with new globe sockets. Must be BK Series 2 HATCH part (04/2006-04/2009). Sedan and Series 1 lights do not fit. - Old socket/clip was damaged by arcing (globe pops out, a previous repair failed). Inspect loom-side H7 connector for heat damage, fit new pigtail if compromised. - Voltage-drop test on the headlight circuit. - New correct-wattage globes: H7 low, HB3 high, parkers/indicators. - Sign-off: run lights 10-15 min, connector stays cool, globe firmly retained, beam aim checked. OPTIONAL EXTRAS - quote each separately, same visit: A. RH rear outer tail light, NEW aftermarket only (current unit heat-damaged and crumbling). Correct-wattage globes, inspect bulb holder and connector for cause of overheating. B. Outer window belt rubber seals, all 4 doors (e.g. Machter WDS-MA001 kit or equivalent). C. Coolant expansion tank (pressurised type, 145 kPa cap). Dried coolant residue around current tank. Confirm leak source (tank/cap/hose) after fitting. D. Rough repair of rear bumper corner scuff (cracked/flaking paint). Sand back, prime, colour-matched aerosol blend (code from VIN). Tidy is fine, showroom not required. E. 7in double-DIN Apple CarPlay head unit (brand-name) replacing the factory stereo, incl facia kit, wiring harness, antenna adapter and steering wheel control interface (wheel buttons must keep working). CarPlay tested with my iPhone. Note wired vs wireless in your quote. LOCATION: Docklands 3008. On-site open parking and street options, or I can drive to your workshop (easier for the paint work). No deadline, flexible timing. Please itemise your offer (core + each extra) with part sources and warranty on parts and workmanship.

There is a fair bit of scratch happened while parking my new Mazda cx-5 car. The scratch is on the right back passenger door near the handle. The red color came out a bit no dent nothing. Can anyone please help with the quote to fix this?. Thanks

Brake Fluid Flush & Bleed – 2011 Mazda 3 (Water Contamination) I accidentally added water to the brake fluid reservoir on my 2011 Mazda 3. The car was driven approximately 560 metres home before I realised, and it has been parked for the last 4–5 days. It is currently not being driven. I’m looking for an experienced mechanic to: * Perform a complete brake fluid flush. * Bleed all four brakes with fresh brake fluid. * Check for any air or water contamination in the brake system. * Inspect the master cylinder and ABS system if required. * Investigate a noise that started after the short drive if it remains after the flush. Please bring all required tools and brake fluid. Experience with brake systems is preferred. Please let me know: * Your experience with this type of job. * Whether you can complete the flush on-site. * Your total price (including brake fluid). Thanks!

Mazda 323 1993 with no spark. I have tested and replaced the Ignition Module as this was the part that has failed previously, no help I have replaced the Ignition coil. I have swapped a spark plug I have tested the crank angle sensor ohms and it seems within normal range. I am not sure how else to diagnose fault at this point and need help to figure it out.

Electrical failure occurred while idling at a traffic light. All instrument cluster indicators illuminated, and the windshield wipers and A/C triggered at full speed independently. After stopping and turning off the engine, the car will not restart. The Start/Stop button shows a solid red light when pressed, and the Immobilizer/Security indicator is blinking on the dash. I have attempted a jump start with a portable pack, but the vehicle remains completely unresponsive. Car currently located in Chadstone

Need front left and right electric window motors replaced on 2010 Mazda CX-9 please. See this YouTube video: https://m.youtube.com/watch?v=CrYwMRUZfSw

back seat seat belt is not retreating on my 2017 mazda CX7

Looking to get an oil change for my Mazda 3 sedan, I live on a main road in st kilda but if you require a private space I am able to organise space in the garage. The car is also low on quite a lot of fluids so if you’re able to provide those additional services I’m more than happy to negotiate with price. Thank you in advance.

Please provide quote to repair the following on a Mazda 2 model year 2007 •⁠ ⁠Source, supply and fit plastic damaged grill •⁠ ⁠⁠Remount front bumper on drivers side •⁠ ⁠⁠Repair and spray damaged paintwork circled

Hi, I’m looking for someone experienced with basic car mechanical work to help with a few jobs: Replace fan belt on my Mazda 3 2010 (automatic) – I already have the replacement belt. Do a transmission service – I’ve got the transmission oil ready. Swap hubcaps on another vehicle – just a straightforward hubcap replacement, all parts supplied. I’ll provide all the supplies (fan belt, transmission oil, and hubcaps). You’ll just need your own tools. Prefer someone who’s done similar work before or is mechanically experienced. Location: Ascot Vale, Melbourne Timing: Mondays and Thursdays & Weekends

I have a scratch on the front of my Mazda 3. No dents. Just scatches. Wondering if someone can fix these. Aesthetic work only.

Replace rear differential in 2007 Mazda MX5. I have a replacement rear differential. No need for oil or any other parts - just labour. Remove existing differential, install replacement differential and replace diff carrier bushing with an aftermarket poly one that I have.

I believe the brake pads on my Mazda 2 - 2010 need changing to new.

Standard service 116,000kms Mazda cx5 2016

Im going to buy a head unit for my car right now and I need somone professional to install it for me please

Fitted seat covers provided by razorback 4x4 , haven’t got images but you refer to razorback website

I need someone to get and fit a new bulb in the tail light and brake light of my 2010 Mazda 2.

My left passenger wheel is needing a new wheel centre hub and bearing willing to pay for this to be fixed if anyone has the parts x