Furniture Refinishing Jobs in California

Browse through over 500 Furniture Refinishing Jobs.

See what you could earn

$0

per month

Based on average furniture refinishing task prices. Actual marketplace earnings may vary

Why join Airtasker

Join Airtasker

Furniture Refinishing tasks in California

Check out what tasks people want done near you right now...

Looking for a highly experienced mechanic to finish a partially completed same-engine swap on my 1990 Ford Bronco 5.8L / 351 Windsor EFI V8. This is NOT a full engine swap from scratch. The original engine has already been removed, and the replacement 5.8L engine has already been lowered into the engine bay. The truck is currently mid-install. The engine still needs to be properly pushed back/aligned, seated onto the motor mounts, mounted, connected, and prepared for startup. The truck has about a 6-inch lift, so please keep that in mind. You must have your own tools and equipment, including a hoist/cherry picker if needed to safely reposition the engine. Current condition: • Replacement engine is in the engine bay but not fully seated/mounted • Upper intake manifold is off and available • Radiator is currently out • Replacement radiator and replacement fan are available • Coolant, transmission fluid, engine oil, and other fluids are already on hand • Replacement engine has a new oil filter installed • Original engine is available for reference/parts if needed Remaining work may include: • Final engine positioning and motor mount alignment • Verifying transmission/bellhousing alignment • Reconnecting engine wiring harness and grounds • Starter connections • Vacuum line routing • Fuel line/system connections • Cooling system, radiator, fan, and hose connections • Upper intake manifold installation • Accessory/belt verification • Fluids, pre-start inspection, startup, and troubleshooting if needed Please only respond if you have real experience with Ford 5.0/5.8 EFI engines, OBS Ford trucks/Broncos, engine swaps, wiring, vacuum routing, and startup troubleshooting. I need someone who can look at the current state, confirm what else may be needed, and finish the swap properly and safely. Please include your experience, earliest availability, whether you have the tools/equipment needed, and whether you’re confident you can complete.

Canoga Park CA 91304 4700, USA

Thu Jun 25 2026

1 day ago

Open

Just need a couple of finish concrete guys to help with small driveway addition as well as some finish work for small slab in backyard.

Anaheim CA 92804, USA

Wed Jun 24 2026

2 days ago

Open

Finish installing a window AC unit and replace the inner air tire in my electric scooter.

Los Angeles CA 90029, USA

Mon Jun 22 2026

4 days ago

Open

11” by 15” re silvering and replacing on the wooden frame.

Tue Jun 16 2026

10 days ago

Open

so i need backerboard put up and refused. then complete water test for drain and vent-- pan is in stalled. connect shower drain and tile. in stall vanity , toilet and shower fixtures for final inspection. Painting as well.

Long Beach CA 90815, USA

Tue Jun 09 2026

17 days ago

Open

Re-insert the top pivot pin back into the track bracket of the door frame so it opens smoothly

Whittier, CA, USA

Fri Jun 05 2026

22 days ago

Open

Tub finish repair. at a minimum i need the peeling paint removed.... and edges smooth... i have touch up paint also. ekopel refinishing paint offer: $40-60. thanks!!

Las Vegas NV 89169, USA

Mon Jun 01 2026

25 days ago

Open

Tub refinish. chipping floor paint sand down touxhup with paint i have

Las Vegas NV 89169, USA

Mon Jun 01 2026

25 days ago

Open

Looking for someone experienced replacing pool deck expansion joints / pool mastic around a concrete pool deck. Current white expansion strips are old, brittle and disintegrating. Want all old material removed and replaced with a clean modern flexible sealant finish (not patching). Scope: * Remove old expansion strip material * Clean/prep joints * Install backer rod where needed * Apply self-leveling pool/deck sealant (Deck-O-Seal, Sikaflex or similar) * Leave with clean, straight, professional finish Pool deck is textured concrete. Approximate joint width: ~1/2” Photos attached. Approximately 55-60 feet Please include: * Experience with similar jobs * Recommended product/system * Estimated timeline * Whether materials are included Require someone who has done pool mastic / expansion joint work before

Mar Vista CA 90066 4501, USA

Thu May 28 2026

29 days ago

Open

Browse all tasks

Last updated on Jun 26th 2026

Unlock new income opportunities in California

Explore furniture refinishing related jobs and discover your financial opportunities

Type of furniture refinishing job	1-2 tasks/week	3-5 tasks/week	5+ tasks/week
Carpentry	$500	$1,250	$1,750
Staining	$360	$900	$1,260
Custom TV Cabinets	$350	$875	$1,225

*Based on average furniture refinishing task prices in California. Actual marketplace earnings may vary

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

We've got you covered

Whether you’re a posting a task or completing a task, you can do both with the peace of mind that Airtasker is there to support.

Airtasker’s insurance cover