Knife Repair Jobs near you

Browse through over 500 knife repair jobs.

See what you could earn

$0

per month

Based on average knife repair task prices. Actual marketplace earnings may vary

Why join Airtasker

Join Airtasker

Knife Repair tasks in United States

Check out what tasks people want done near you right now...

Stop a Thompson bandsaw from screeching when blade stops

Rocklea QLD, Australia

Fri Feb 13 2026

about 11 hours ago

Open

ooking for an affordable carpet layer who can supply and install new carpet for a 4‑bedroom home plus hallway in Mernda. House is vacant, no furniture, easy access — ideal for a quick, low‑cost job. • Supply budget‑friendly carpet (standard rental/sale grade) • Supply underlay • Install carpet in 4 bedrooms + hallway • Stretching, trimming, fitting • Replace smooth edge if needed • Basic prep only — floors will be cleared Budget Focus: • Looking for good value, not premium finishes • Happy with standard colours (charcoal/grey preferred) • Open to end‑of‑rolls, discontinued stock, or leftover bulk carpet • We will remove and dispose of all old carpet ourselves to reduce costs We Provide: • Empty house • Clear access • Removal of old carpet and waste • Flexible timing You Provide: • Carpet + underlay • Labour • Tools, knives, stretcher, smooth edge (if needed) Please include in your quote: • Total price for carpet + underlay + installation • Carpet type/colour options • Estimated time to complete • Your availability

Mernda VIC, Australia

Fri Feb 13 2026

about 12 hours ago

Open

Kayak Rudder Replacement & Minor Fix – Parts Supplied On Site (30–60 mins) We require a handyman/technician to attend a residential address and carry out a straightforward parts swap and minor fix on a fishing kayak. All replacement parts will be on site and ready at the customer’s home. No sourcing required. This is not a complex marine job — it’s primarily a remove-and-replace task. Estimated time: 30–60 minutes. ⸻ Scope of Work: 1. Remove existing rudder system from Kayak A 2. Install supplied SmartTrack Hybrid Foil rudder system 3. Install supplied rudder blade guide 4. Install supplied rear deck bungee cord 5. Rectify exposed wire/cable on Kayak B • Secure and properly cover the exposed section • Ensure it cannot scratch or cause injury • Neatly fasten and finish ⸻ Important Notes: • All parts will be supplied and present at the property • No specialist kayak knowledge required • Basic mechanical competence and attention to detail is sufficient • Standard hand tools should be adequate • Ensure both kayaks are left consistent, tidy, and safe ⸻ Completion Requirements: Before leaving site, technician must: 1. Confirm rudder moves freely and deploys correctly 2. Confirm bungee cord is properly tensioned and secured 3. Confirm wire/cable is fully covered and safe 4. Take clear photos of: • Installed rudder • Rudder blade guide • Rear bungee cord • Rectified wire area • Full rear view of both kayaks Photos must be submitted immediately after completion.

Highett VIC 3190, Australia

Fri Feb 13 2026

about 15 hours ago

Open

My driver side wiper blade isn’t working

Gladstone QLD, Australia

Wed Feb 11 2026

2 days ago

Open

Petrol mower blade is tuck and machine needs service Battery mower was left in the rain ( ! ) and now starts but dies

Canada Bay NSW 2046, Australia

Tue Feb 10 2026

3 days ago

Open

Am not able to insert a cutting blade. Philips Homecooker set, 2015, never used. Have tried hair dryer, freezing and soaking in warm, soapy water.

Oran Park NSW, Australia

Mon Feb 09 2026

4 days ago

Open

Please send through a quote and lead times for installation for timber/composite decking. Area size: L 3500 mm * W 2700 mm * H 160 mm We also need the bamboo panels screening done on existing timber fence. Area: L 12 M, H 2.4 M And blade aluminium fencing at the front. Area: L 13 M, H 1.2/ 1.4 M Thank you

Tarneit VIC 3029, Australia

Sun Feb 08 2026

5 days ago

Open

The hair straightener (cloudenine) was working fine till yesterday but this morning the red light flashes but blade plates do not get heated.

Parramatta NSW, Australia

Sun Feb 08 2026

5 days ago

Open

Service and sharpen blades Scott Bonner reel mower.

Iluka WA 6028, Australia

Sun Feb 08 2026

6 days ago

Open

Browse all tasks

Last updated on Feb 13th 2026

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

Get Inspired: Top Knife Repair Taskers in United States

meet
David R
3 years on Airtasker
- Los Angeles California
5
Overall rating
58 reviews
100%
Completion rate
The percentage of tasks successfully completed by the Tasker
67 tasks
meet
Kevin R
10 months on Airtasker
5
Overall rating
3 reviews
100%
Completion rate
The percentage of tasks successfully completed by the Tasker
5 tasks
meet
Kendall S
9 months on Airtasker
- Austin Texas
5
Overall rating
6 reviews
100%
Completion rate
The percentage of tasks successfully completed by the Tasker
8 tasks
meet
Gary R
6 months on Airtasker
- San Diego California
5
Overall rating
4 reviews
100%
Completion rate
The percentage of tasks successfully completed by the Tasker
5 tasks